MAX1396EVKIT Maxim Integrated, MAX1396EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX1396EVKIT
• Description: Data Conversion IC Development Tools Evaluation Kit for the MAX1391/MAX1392/MAX1393/MAX1394/MAX1395/MAX1396
• Manufacturer: Maxim Integrated
• Series: MAX1393, MAX1396r

Specifications of MAX1396EVKIT

• Interface Type: Serial

MAX1396 Evaluation Kit
Note: Indicate you are using the MAX1391–MAX1396 when
contacting these manufacturers.
2
DESIGNATION QTY
Citizen America
Corporation
TDK
SUPPLIER
_______________________________________________________________________________________
U7, U8
U10
R11
R12
R13
R14
R15
U1
U2
U3
U4
U5
U6
U9
Y1
Y2
—
—
—
—
Component List (continued)
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
7
1
1
1
949-428-3700
847-803-6100
PHONE
Component Suppliers
102kΩ ±1% resistor (0603)
54.9kΩ ±1% resistor (0603)
24kΩ ±1% resistor (0603)
93.1kΩ ±1% resistor (0603)
10kΩ ±5% resistor (0603)
MAX1396ETB (10-pin TDFN)
MAXQ2000-RAX (68-pin QFN-EP)
FTDI FT232BL (7mm x 7mm,
32-pin TQFP-L)
AT93C 46A 3- w i r e E E P RO M ( 8- p i n S O)
MAX890LESA (8-pin SO)
MAX8511EXK25-T (5-pin SC70)
Top mark: ADV
MAX8512EXK-T (5-pin SC70)
Top mark: ADW
MAX3376EEKA-T (8-pin SOT23)
MAX3375EEKA-T (8-pin SOT23)
20MHz crystal
6MHz crystal
Shunts
USB cable
MAX1396 PC board
MAX1396 EV kit software CD-ROM
DESCRIPTION
www.citizencrystal.com
www.component.tdk.com
WEBSITE
1) Make sure the shunts of all jumpers are in the right
2) Connect the signal source to the AIN1 pad and the
3) Set the signal source to +1V.
_________________________Quick Start
INSTALL.EXE
MAX1396.EXE
FTDIBUS.INF
FTDIPORT.INF
UNINST.INI
TROUBLESHOOTING_USB.PDF
• MAX1396 EV kit (USB cable included)
• MAX1396 evaluation kit software (downloaded
• Signal source to drive ADC input
• Windows 98 SE/2000/XP-compatible PC
• Available USB port on the PC
position.
JU1: (1-2) VCC connected to on-board +1.54V
voltage regulator.
JU2: (1-2) CH1/CH2 connected to on-board µC
through a voltage-level translator.
JU3: (1-2) OE connected to on-board µC through a
voltage-level translator.
JU4: (1-2) CS connected to on-board µC through a
voltage-level translator.
JU5: (1-2) SCLK connected to on-board µC through
a voltage-level translator.
JU6: (1-2) DOUT connected to on-board µC
through a voltage-level translator.
JU7: (1-2) Reference voltage connected to VCC.
GND terminal of the signal source to the GND pad.
Connect AIN2 to GND.
from www.maxim-ic.com)
FILE
Recommended Equipment
MAX1396EVKIT Files
Installs the EV kit files on
your computer
Application program
USB device driver file
VCP device driver file
Uninstalls the EV kit
software
USB driver installation help
file
DESCRIPTION
Procedure