DM330023-2 Microchip Technology, DM330023-2 Datasheet - Page 38

• Manufacturer Part Number: DM330023-2
• Description: Power Management IC Development Tools dsPICDE MCHV-2
• Manufacturer: Microchip Technology
• Type: Motor / Motion Controllers & Driversr

Specifications of DM330023-2

• Rohs: yes
• Product: Development Boards
• Tool Is For Evaluation Of: PIC24F, PIC24E, dsPIC33F, dsPIC33E
• Input Voltage: 90 V to 265 V
• Output Voltage: 15 V
• Interface Type: UART
• Output Current: 0.75 A
• For Use With: PIC24F, PIC24E, dsPIC33F, dsPIC33E

DS52074A-page 38
The 3.3 volts rail is created using a step-down regulator which is attached to the 15
volts regulator. The maximum output current is 0.650A, thus the resultant maximum
power is 2.145W.
The 3.3 volts rail required for the analog circuits such as the current feedback and the
Analog-to-digital converter is generated by a decoupling circuitry attached to the 3.3 volts
regulator.
4.1.5
Given the development nature of the system, robust independent FAULT protection is
provided on the PFC Stage Board. Two different fault categories are used to indicate a
FAULT to the PIC24 MCU or dsPIC DSC.
DC Bus Overcurrent, this fault signal is generated when the maximum current limit of
15A is reached. The comparison of the threshold value and the actual current is done
by comparator U8. The threshold limit is set by R56 and R57. R69 is a shunt jumper
resistor that can disconnect the overcurrent fault to the PIC24 MCU or dsPIC DSC.
DC Bus Overvoltage, this fault signal is generated when the maximum voltage limit on
the DC bus rails is reached. The threshold value is set to 432V. The comparison of the
threshold value and the actual DC bus voltage is done by comparator U7. The thresh-
old limit is set by R60, R61 and R62. R66 is a shunt jumper resistor that can disconnect
the overvoltage fault to the PIC24 MCU or dsPIC DSC.
4.1.6
The PFC stage board has four tab fast-on connectors, one AC inlet and one 14-pin
keyed connector for attaching a flat cable.
For the AC mains supply input, standard double-insulated, 3-core flex cable should be
used with a minimum current rating of 10A (1 mm
can be used. The recommended cable size is 1.0 to 1.5 mm
have a 600V rating. This cable should also be double insulated or have a protective
ground screen.
The tab fast-on connectors AC_N and AC_L provides the connections to the bridge
rectifier BR1. The recommended cable size is 16-18 AWG or 1.0 to 1.5 mm
recommended that cables used for the power connections should be terminated with
blue or red crimp terminals. If crimp terminals are not used, care should be taken to
ensure that stray strands of wire do not short to adjacent terminals or the enclosure. If
possible, all wires should be stripped and tinned with solder before connecting to the
dsPICDEM MCHV-2 Development Board terminals.
Note:
Note 1:
2:
Fault Circuitry
Board Connectors
Both comparators are of open-drain type and need an external pull-up
resistor. Both circuits share this pull-up resistor creating an OR condition at
the output.
The system is designed for installation category II. Therefore, the
incoming mains cable should be wired into a standard non-locking 2-pin
in addition with an earth ground type plug.
The unit is designed to be connected to the AC mains supply via a
standard non-locking plug. As the unit has no mains switch, this plug
constitutes the means of disconnection from the supply. Therefore, the
user must have unobstructed access to this plug during operation.
2
18 AWG). A computer power cable
2
 2012 Microchip Technology Inc.
(18-16 AWG) and it should
2
. It is also