MAX1363EVKIT Maxim Integrated, MAX1363EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX1363EVKIT
• Description: Data Conversion IC Development Tools Evaluation Kit for the MAX1361/MAX1363
• Manufacturer: Maxim Integrated
• Series: MAX1363, MAX1364r

Specifications of MAX1363EVKIT

• Interface Type: I2C, Serial
• Operating Supply Voltage: 2.7 V to 3.6 V

• MAX1363 EV kit
• Signal source from 0 to 3.6V
• Windows 98 SE-/2000-/XP-compatible PC
• Spare USB port on the PC
MAX1363 Evaluation Kit
Note: Indicate you are using the MAX1363 when contacting
these component suppliers.
2
µMAX is a registered trademark of Maxim Integrated Products, Inc.
Citizen
America
Corporation
TDK
DESIGNATION
SUPPLIER
_______________________________________________________________________________________
R14
R18
R22
TRX
TP1
U1
U2
U3
U4
U5
U7
U8
Y1
Y2
—
—
—
Component List (continued)
949-428-3700
847-803-6100
QTY
1
1
1
0
1
1
1
1
1
1
1
1
1
1
6
1
1
PHONE
Component Suppliers
Recommended Equipment
10kΩ ±5% resistor (0603)
1kΩ ±5% resistor (0603)
47kΩ ±5% resistor (0603)
Not installed
Yellow LED (0603)
MAX1363EUB (10-pin µMAX
MAX6018AEUR21 (3-pin SOT23)
MAXQ2000-RAX (68-pin QFN-EP)
FTDI FT232BL (7mm x 7mm 32-lead
TQFP)
AT93C46A type 3-wire EEPROM
(8-pin SO)
MAX8511EXK33-T (5-pin SC70)
Top mark: AEI
MAX8511EXK25-T (5-pin SC70)
Top mark: ADV
20MHz crystal
6MHz crystal
Shunts
MAX1363 EV kit PC board
MAX1363 EV kit software CD-ROM
www.citizencrystal.com
www.component.tdk.com
DESCRIPTION
Quick Start
WEBSITE
®
)
1) Make sure the shunts of all jumpers are in the right
2) Connect the GND terminal of the signal source to
3) Set the signal source to 1V.
4) Install the MAX1363 evaluation software on your com-
5) Connect the USB cable from the PC to the
TROUBLESHOOTING_USB.PDF
position.
JU1: (1-2) I
JU2: (Open) AIN3 is an input
JU3: (1-2) USB powered
JU4: (1-2) SDA connected to on-board microcon-
troller (µC)
JU5: (1-2) SCL connected to on-board µC
JU6: (1-2)
See
MAX1361_EUB, and MAX1363_EUB.
the AGND pad and the signal source to the AIN0
pad. Connect AIN1, AIN2, and AIN3 to GND.
puter by running the INSTALL.EXE program on the
installation CD-ROM. The program files are copied
and icons are created in the Windows Start menu.
MAX1363 EV kit. A Building Driver Database win-
dow pops up in addition to a New Hardware
Found message. If you do not see a window that is
similar to the one described above after 30
seconds, remove the USB cable from the MAX1363
EV kit and reconnect it again. Administrator privi-
leges are required to install the USB device driver
on Windows 2000 and Windows XP. Refer to the
TROUBLESHOOTING_USB.PDF document includ-
ed with the software for more information.
HELPFILE.HTM
FTDIPORT.INF
MAX1363.EXE
Table
INSTALL.EXE
FTDIBUS.INF
UNINST.INI
FILE
INT connected to on-board µC
2
C slave address = 0x6A
1 when using the MAX1361EUB,
MAX1363 EV kit Files
Installs the EV kit files on
your computer
Application program
Help file
USB device-driver file
VCP device-driver file
U ni nstal l s the E V ki t softw ar e
USB driver installation help
file
DESCRIPTION
Procedure