IS61C1024AL-12TI ISSI, Integrated Silicon Solution Inc, IS61C1024AL-12TI Datasheet
IS61C1024AL-12TI
Specifications of IS61C1024AL-12TI
Related parts for IS61C1024AL-12TI
IS61C1024AL-12TI Summary of contents
Page 1
... Easy memory expansion is provided by using two Chip Enable inputs, CE1 and CE2. The active LOW Write Enable (WE) controls both writing and reading of the memory. The IS61C1024AL/IS64C1024AL is available in 32-pin 300- mil SOJ, 32-pin 400-mil SOJ, 32-pin TSOP (Type I, 8x20), and 32-pin sTSOP (Type 13.4) packages. ...
Page 2
... L Read H L Write PIN CONFIGURATION 32-Pin TSOP (Type 1) (T) and sTSOP (Type 1) (H) A11 A13 CE2 6 A15 7 VDD A16 10 A14 11 A12 OPERATING RANGE (IS61C1024AL) Range Commercial Industrial OPERATING RANGE (IS64C1024AL) Range Automotive CE2 I/O Operation High High High OUT Integrated Silicon Solution, Inc. — www.issi.com — ...
Page 3
... IS61C1024AL, IS64C1024AL ABSOLUTE MAXIMUM RATINGS Symbol Parameter V Terminal Voltage with Respect to GND TERM T Storage Temperature STG P Power Dissipation Output Current (LOW) OUT Notes: 1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the opera- tional sections of this specification is not implied ...
Page 4
... IS61C1024AL, IS64C1024AL IS61C1024AL/IS64C1024AL POWER SUPPLY CHARACTERISTICS Symbol Parameter Test Conditions I V Operating Supply Current Dynamic Operating Supply Current I I TTL Standby Current (TTL Inputs) V CE1 V CE2 V I CMOS Standby CE1 V Current (CMOS Inputs) CE2 0. Note address and data inputs are cycling at the maximum frequency means no input lines change. ...
Page 5
... IS61C1024AL, IS64C1024AL READ CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Read Cycle Time RC t Address Access Time AA t Output Hold Time OHA CE1 Access Time t 1 ACE t CE2 Access Time 2 ACE OE Access Time t DOE OE to Low-Z Output t (2) LZOE OE to High-Z Output t (2) ...
Page 6
... IS61C1024AL, IS64C1024AL AC WAVEFORMS (1,2) READ CYCLE NO. 1 ADDRESS D OUT PREVIOUS DATA VALID (1,3) READ CYCLE NO. 2 ADDRESS OE CE1 CE2 t LZCE1 t LZCE2 HIGH-Z D OUT Notes HIGH for a Read Cycle. 2. The device is continuously selected. OE, CE1 = V 3. Address is valid prior to or coincident with CE1 LOW and CE2 HIGH transitions. ...
Page 7
... IS61C1024AL, IS64C1024AL WRITE CYCLE SWITCHING CHARACTERISTICS Symbol Parameter t Write Cycle Time WC CE1 to Write End t 1 SCE t CE2 to Write End 2 SCE t Address Setup Time to Write End AW t Address Hold from Write End HA t Address Setup Time SA WE Pulse Width t (3) PWE t Data Setup to Write End ...
Page 8
... IS61C1024AL, IS64C1024AL AC WAVEFORMS WRITE CYCLE NO. 1 (CE1 Controlled HIGH or LOW) ADDRESS t SA CE1 CE2 WE D DATA UNDEFINED OUT D IN WRITE CYCLE NO. 2 (OE is HIGH During Write Cycle) ADDRESS OE CE1 LOW HIGH CE2 DATA UNDEFINED OUT D IN Notes: 1. The internal write time is defined by the overlap of CE1 LOW, CE2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to terminate the Write ...
Page 9
... IS61C1024AL, IS64C1024AL WRITE CYCLE NO. 3 (OE is LOW During Write Cycle) ADDRESS OE LOW CE1 LOW HIGH CE2 DATA UNDEFINED OUT D IN Integrated Silicon Solution, Inc. — www.issi.com — Rev. B 01/24/05 ( VALID ADDRESS PWE2 t HZWE HIGH DATA VALID IN 1-800-379-4774 ISSI ® LZWE CE2_WR3.eps ...
Page 10
... IS61C1024AL, IS64C1024AL DATA RETENTION SWITCHING CHARACTERISTICS Symbol Parameter V V for Data Retention Data Retention Current DR t Data Retention Setup Time SDR t Recovery Time RDR Note: 1. Typical Values are measured 5V DATA RETENTION WAVEFORM (CE1 VDD 4.5V 2. CE1 GND DATA RETENTION WAVEFORM (CE2 Controlled) VDD 4 ...
Page 11
... ORDERING INFORMATION: IS61C1024AL Industrial Range: –40°C to +85°C Speed (ns) Order Part No. 12 IS61C1024AL-12JI IS61C1024AL-12JLI IS61C1024AL-12KI IS61C1024AL-12KLI IS61C1024AL-12HI IS61C1024AL-12TI IS61C1024AL-12TLI ORDERING INFORMATION: IS64C1024AL Automotive Range: –40°C to +125°C Speed (ns) Order Part No. 15 IS64C1024AL-15KA3 IS64C1024AL-15TA3 Integrated Silicon Solution, Inc. — www.issi.com — ...
Page 12
PACKAGING INFORMATION Plastic STSOP - 32 pins Package Code: H (Type I) 1 Plastic STSOP (H - Type I) Millimeters Symbol Min Max Ref. Std — 1.25 A1 0.05 — A2 0.95 1.05 b 0.17 0.23 C ...
Page 13
PACKAGING INFORMATION 400-mil Plastic SOJ Package Code Millimeters Inches Symbol Min Max Min No. Leads ( 3.25 3.75 0.128 0.148 A1 0.64 — 0.025 A2 2.08 — 0.082 B 0.38 0.51 0.015 0.020 ...
Page 14
PACKAGING INFORMATION Millimeters Inches Symbol Min Max Min No. Leads ( 3.25 3.75 0.128 0.148 A1 0.64 — 0.025 A2 2.08 — 0.082 B 0.38 0.51 0.015 0.020 b 0.66 0.81 0.026 0.032 C 0.18 0.33 0.007 0.013 ...
Page 15
PACKAGING INFORMATION 300-mil Plastic SOJ Package Code MILLIMETERS Sym. Min. Typ. Max. N0. Leads 24/26 A — — 3.56 A1 0.64 — — A2 2.41 — 2.67 b 0.41 — 0.51 B 0.66 — 0.81 ...
Page 16
PACKAGING INFORMATION 300-mil Plastic SOJ Package Code: J MILLIMETERS Sym. Min. Typ. Max. Min. Typ. Max. N0. Leads 28 A — — 3.56 — A1 0.64 — — 0.025 A2 2.41 — 2.67 0.095 b 0.41 — 0.51 0.016 B ...
Page 17
PACKAGING INFORMATION Plastic TSOP-Type I Package Code: T (32-pin MILLIMETERS Symbol Min. Max. No. Leads A — 1.20 A1 0.05 0.25 B 0.17 0.23 C 0.12 0.17 D 7.90 8.10 E 18.30 18.50 H 19.80 20.20 e ...