MAX6964EVKIT Maxim Integrated, MAX6964EVKIT Datasheet - Page 2

• Manufacturer Part Number: MAX6964EVKIT
• Description: LED Lighting Development Tools Evaluation Kit for the MAX6964
• Manufacturer: Maxim Integrated
• Series: MAX6964r

Specifications of MAX6964EVKIT

• Product: Evaluation Kits

MAX6964 Evaluation Kit/Evaluation System
Note: Indicate that you are using the MAX6964 when contacting
these component suppliers.
2
AVX Corp.
Fairchild
Semiconductor
M ur ata M fg . C o., Ltd . 770-436-1300 www.murata.com
OP TE K Technol og i es 972-323-2200 www.optekinc.com
SANYO Electronic
Device
Taiyo Yuden
TDK
R7, R10, R13, R16
R8, R11, R14, R17
TROUBLESHOOTING_USB.PDF
R6, R9, R12, R15
DESIGNATION
_______________________________________________________________________________________
SUPPLIER
R18, R19
U2, U3
R1–R5
SW1
R20
R21
U1
—
—
Component Lists (continued)
MAX6964.EXE
INSTALL.EXE
FTD2XX.INF
UNINST.INI
FILE
QTY
843-946-0238 www.avxcorp.com
888-522-5372 www.fairchildsemi.com
619-661-6835 www.sanyodevice.com
800-348-2496 www.t-yuden.com
847-803-6100 www.component.tdk.com
5
4
4
4
2
1
1
1
1
2
5
1
MAX6964 EV Kit Files
Component Suppliers
PHONE
110Ω ±5% resistors (0603)
68Ω ±5% resistors (0603)
120Ω ±5% resistors (0603)
130Ω ±5% resistors (0603)
165kΩ ±1% resistors (0603)
82.5kΩ ±1% resistor (0603)
10kΩ ±5% resistor (0603)
SPST momentary contact switch
Maxim 17-output LED driver/GPO
MAX6964AEG (24-pin QSOP)
TinyLogic HS inverter with Schmitt
trigger input (SC70-5)
Fairchild NC7S14P5X
Shunts (JU1–JU5)
PCB: MAX6964 Evaluation Kit+
Installs the EV kit files on
your computer
Application program
USB device driver file
U ni nstal l s the E V ki t softw ar e
USB driver installation
help file
DESCRIPTION
DESCRIPTION
WEBSITE
•
•
•
•
Note: In the following sections, software-related items
are identified by bolding. Text in bold refers to items
directly from the EV kit software. Text in bold and
underlined refers to items from the Windows
98SE/2000/XP operating system.
The MAX6964 EV kit is fully assembled and tested.
Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
1) Visit www.maxim-ic.com/evkitsoftware to download
2) Install the EV kit software on your computer by run-
3) Verify that a shunt is installed on the 3.3V pins of
4) Verify that a shunt is installed on pins 2-3 of jumper
5) Verify that a shunt is installed on pins 1-3 of jumper
6) Verify that a shunt is installed on pins 2-3 of jumper
7) Verify that a shunt is installed on jumpers JU4 and
8) Utilizing short leads, connect the 5V power supply
9) Connect the CMAXQUSB interface board to the
5V, 0.5A-rated DC power supply
Maxim MAX6964 EV kit and CMAXQUSB interface
board
Windows 98SE/2000/XP-compatible PC with a spare
USB port
USB I/O extension cable, straight-through, male-to-
female cable
the latest version of the EV kit software,
6964Rxx.ZIP. Save the EV kit software to a tempo-
rary folder and uncompress the ZIP file.
ning the INSTALL.EXE program inside the temporary
folder. The program files are copied and icons are
created in the Windows Start | Programs menu.
jumper JU1 (VDD SELECT) on the CMAXQUSB inter-
face board. This process configures the CMAXQUSB
interface board VDD SELECT supply to 3.3V.
JU1 (CMAXQUSB V
EV kit.
JU2 (0x40 address).
JU3 (OSC signal).
JU5 (3Hz blink rate).
to the EV kit’s VLED PCB pad. Utilizing short leads,
connect the power-supply ground to the EV kit’s
GND PCB pad near the VLED pad.
MAX6964 EV kit’s J1 connector.
DD
Hardware Configuration
MAX6964 Software and
supplies V+) on the MAX6964
Required Equipment
Quick Start