ZICM357SP2-1C-B CEL, ZICM357SP2-1C-B Datasheet - Page 12
![no-image](/images/manufacturer_photos/0/1/129/cel_sml.jpg)
ZICM357SP2-1C-B
Manufacturer Part Number
ZICM357SP2-1C-B
Description
Zigbee / 802.15.4 Modules 2.4GHz, OP=20dBm Vdd 3.6Volt Max.
Manufacturer
CEL
Datasheet
1.ZICM-EM35X-DEV-KIT-2.pdf
(14 pages)
Specifications of ZICM357SP2-1C-B
Rohs
yes
Frequency Band
2.405 GHz to 2.48 GHz
Data Rate
250 Kbps
Sensitivity
- 103 dBm
Operating Supply Voltage
- 0.3 VDC to + 3.5 VDC
Supply Current Transmitting
58 mA
Supply Current Receiving
34 mA
Output Power
20 dBm
Antenna Connector Type
External
Dimensions
0.94 in x 0.655 in
AGENCY CERTIFICATIONS
The OEM of the MeshConnect Module may only use the approved antenna, (PCB Trace Antenna) that has been certified
with this module. The OEM of the MeshConnect Module must test their final product configuration to comply with Uninten-
tional Radiator Limits before declaring FCC compliance per Part 15 of the FCC rules.
IC Certification — Industry Canada Statement
The term "IC" before the certification/registration number only signifies that the Industry Canada technical specifications
were met.
Certification IC - Déclaration d'Industrie Canada
Le terme "IC" devant le numéro de certification/d'enregistrement signifie seulement que les spécifications techniques
Industrie Canada ont été respectées.
Section 14 of RSS-210
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field
in excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada's
website:
L'article 14 du CNR-210
Le programme d'installation de cet équipement radio doit s'assurer que l'antenne est située ou orientée de telle sorte qu'il ne
pas émettre de champ RF au-delà des limites de Santé Canada pour la population générale. Consulter le Code de sécurité 6,
disponible sur le site Web de Santé Canada:
CE Certification — Europe
The MeshConnect ZICM357SP0 module has been tested and certified for use in the European Union.
OEM Responsibility to the European Union Compliance Rules
If the MeshConnect module is to be incorporated into a product, the OEM must verify compliance of the final product to the
European Harmonized EMC and Low-Voltage / Safety Standards. A Declaration of Conformity must be issued for each of
these standards and kept on file as described in Annex II of the R&TTE Directive.
The manufacturer must maintain the user's guide and adhere to the settings described in the manual for maintaining
European Union Compliance. If any of the specifications are exceeded in the final product, the OEM is required to
make a submission to the notified body for compliance testing.
OEM Labeling Requirements
The CE mark must be placed on the OEM product in a visible location.
The CE mark shall consist of the initials “CE” with the following form:
· If the CE marking is reduced or enlarged, the proportions given in the above graduated
· The CE mark must be a minimum of 5mm in height
· If the use of the module is subject to restrictions in the end application, the CE
drawing must be adhered to.
marking on the OEM product should also include the alert sign as shown in the
picture to the right.
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/99ehd-dhm237/index-eng.php
(Continued)
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/99ehd-dhm237/index-eng.php
MeshConnect™ EM357 Mini Modules
Page 12