HV853DB1 Supertex, HV853DB1 Datasheet

no-image

HV853DB1

Manufacturer Part Number
HV853DB1
Description
Power Management IC Development Tools INDUCTORLESS EL LAMP DRIVER DEMOBOARD
Manufacturer
Supertex
Datasheet

Specifications of HV853DB1

Product
Power Management Development Tools
Tool Is For Evaluation Of
HV853
Description/function
EL Driver Demo Board
Factory Pack Quantity
1
General Description
The Supertex HV853DB1 demoboard contains all the
necessary circuitry to demonstrate the features of the HV853
EL lamp driver. The HV853 is the low noise version of the EL
driver HV852 with improved EMI performance.
Simply connect it to a power supply and a lamp as shown in
Figure 1. For additional assistance with the HV853 demoboard
circuit, please refer to the HV853 datasheet.
Board Layout and Connection Diagram
Connections:
V
Supplies the HV853 EL driver IC. The supplied demoboard
is optimized for 3.2 to 5.0V operation.
EN (Enable Input)
A logic input which enables/disables the driver. Connect EN
to logic high (V
to disable the driver. This input may be connected to a me-
chanical switch or to a logic circuit output.
CLK
A logic input pin to which an external clock can be applied
to set the EL lamp frequency. CLK
V
needs to be removed and the R
to ground. Connect CLK
Note:
Supertex inc.
DD
DD
All of the above connections must be made before powering up the supply voltages.
when external clock input is used. Also, the R
(IC Supply)
IN
(Clock Input)
Supertex inc.
DD
) to enable the driver and to logic low (GND)
High Voltage, Low Noise, Inductorless
IN
to GND if not used.
CLKIN
GND
VDD
EL
EN
pin needs to be connected
EL Lamp Driver Demoboard
EN
has to be connected to
1235 Bordeaux Drive, Sunnyvale, CA 94089
Actual Dimensions: 13mm x 8mm
EL
resistor
GND (Circuit Ground)
Connect to V
for V
pass capacitors are not required.
V
They connect to EL lamp terminals. Polarity is irrelevant.
CLK
Logic input pin which enables/disables the external clock ap-
plied. Logic high (V
be set by the CLK
lamp frequency to be set by the external R
A
Specifications
Parameter
Input voltage:
Supply current:
Lamp size:
Lamp frequency:
and V
EN
DD
is provided on the demoboard. External supply by-
(Clock Enable)
B
(Lamp Connections)
DD
Tel: 408-222-8888
negative terminal. Supply bypass capacitor
IN
DD
input. Logic low (GND) will cause the EL
) will cause the EL lamp frequency to
VA
VB
CLKEN
www.supertex.com
HV853DB1
0.93in
EL
resistor.
3.2V to 5.0V
2
and 1.5in
274Hz
Value
18mA
2

Related parts for HV853DB1

HV853DB1 Summary of contents

Page 1

... Supertex inc. High Voltage, Low Noise, Inductorless General Description The Supertex HV853DB1 demoboard contains all the necessary circuitry to demonstrate the features of the HV853 EL lamp driver. The HV853 is the low noise version of the EL driver HV852 with improved EMI performance. Simply connect power supply and a lamp as shown in Figure 1 ...

Page 2

... Package 0603 0603 DFN-10 does not assume responsibility for use of devices described, and limits its liability Supertex inc. Supertex inc. 2 HV853DB1 EL Lamp = 1.6MΩ. The following was observed when EL Brightness f EL (Hz) ft-lm 274 5.71 19.53 274 5.91 20.20 274 6.08 20.80 274 6.20 21.21 274 5.27 18.03 274 5 ...

Related keywords