MAX17019EVKIT+ Maxim Integrated, MAX17019EVKIT+ Datasheet - Page 3

• Manufacturer Part Number: MAX17019EVKIT+
• Description: Power Management IC Development Tools Maxim Evaluation Kit
• Manufacturer: Maxim Integrated
• Series: MAX17019r

Note: Indicate that you are using the MAX17019 when contacting these component suppliers.
• MAX17019 EV kit
• 5.5V to 38V DC power supply
• Four digital multimeters (DMMs)
• 100MHz dual-trace oscilloscope
The MAX17019 EV kit is a fully assembled and tested
surface-mount board. Follow the steps below to verify
board operation. Caution: Do not turn on the power
supply until all connections are completed.
1) Ensure that the circuit is connected correctly to the
2) Set SW1 (1, 10) to the off position (SHDN = VBATT,
Central Semiconductor Corp.
Fairchild Semiconductor
Murata Electronics North America, Inc.
NEC TOKIN America, Inc.
SANYO NA Corp.
Taiyo Yuden
TDK Corp.
TOKO America, Inc.
Vishay
Würth Electronik GmbH & Co. KG
DESIGNATION QTY
power supply and dummy loads prior to applying any
power.
MAX17019 disabled).
Set SW1 (2, 9) to the on position (ONA = VDD, VOUTA
enabled).
Set SW1 (3, 8) to the on position (ONB = VDD, VOUTB
enabled).
R27, R28
R25
R26
R32
R33
SUPPLIER
_______________________________________________________________________________________
1
1
0
1
1
51I Q5% resistor (0402)
0.004I Q1% 1/4W resistor (1206)
Vishay (Dale) WSL12064L000FEA
Not installed, resistors—short (PC
trace) (0612)
82.5kI Q5% resistor (0402)
1kI Q5% resistor (0603)
Recommended Equipment
DESCRIPTION
Quick Start
Procedure
631-435-1110
888-522-5372
770-436-1300
408-324-1790
619-661-6835
800-348-2496
847-803-6100
847-297-0070
402-563-6866
201-785-8800
MAX17019 Evaluation Kit
PHONE
*EP = Exposed pad.
3) Connect the first DMM across the VOUTA and GND
4) Connect the second DMM across the VOUTB and
5) Connect the third DMM across the VOUTC and GND
6) Connect the fourth DMM across the VOUTD and GND
7) Turn on the power supply and adjust input voltage to
8) Set SW1 (1, 10) to the on position (SHDN = VBATT,
9) All LEDs should be lit; verify that the output voltages
DESIGNATION QTY
Component Suppliers (continued)
Set SW1 (4, 7) to the on position (ONC = VDD,
VOUTC enabled).
Set SW1 (5, 6) to the on position (OND = VDD,
VOUTD enabled).
pads.
GND pads.
pads.
pads.
12V.
MAX17019 activated).
are VOUTA = 5V, VOUTB = 3.3V, VOUTC = 1.2V, and
VOUTD = 2.5V.
SW1
U1
—
www.centralsemi.com
www.fairchildsemi.com
www.murata-northamerica.com
www.nec-tokinamerica.com
www.sanyodevice.com
www.t-yuden.com
www.component.tdk.com
www.tokoam.com
www.vishay.com
www.we-online.com
1
1
1
Component Suppliers
5-position, low-profile DIP switch
Quad output controller
(48 TQFN-EP*)
Maxim MAX17019ATM+
PCB: MAX17019 EVALUATION KIT+
WEBSITE
DESCRIPTION
3