AMIS30585GEVK ON Semiconductor, AMIS30585GEVK Datasheet - Page 13

• Manufacturer Part Number: AMIS30585GEVK
• Description: Power Management IC Development Tools EVK PLC MODEM 1200 BAUD
• Manufacturer: ON Semiconductor
• Type: Supervisory Circuitsr

Specifications of AMIS30585GEVK

• Rohs: yes
• Product: Evaluation Kits
• Tool Is For Evaluation Of: AMIS-30585
• Input Voltage: 3 V to 3.6 V
• Output Voltage: 0.3 V

16. Input at RX_IN, no other external components.
17. This parameter will be characterized on a limited number of prototypes and will not be tested in production.
18. A sinusoidal signal of 10 kHz and 100 mV ptp is injected between VDDA and VSSA. The signal level at the differential LPF_OUT and
19. A sinusoidal signal of 50 Hz and 100 mV ptp is injected between VDDA and VSSA. The signal level at the differential LPF_OUT output is
20. These parameters will be tested in production with an input signal of 95 kHz and 1 Vp by reading out the digital samples at the point AD_OUT
have a frequency characteristic between the limits listed
below. The absolute output level depends on the operating
condition. In production the measurement will be done for
relative output levels where the 0 dB reference value is
measured at 50 kHz with a signal amplitude of 100 mV.
Table 13. RECEIVER EXTERNAL PARAMETERS: Pin RX_IN, RX_OUT, REF_OUT
IMax_REF_OUT
The receive LPF filter + AGC + low noise amplifier must
VOFFS_RX_IN
VOFFS_RX_IN
PSRR
REF_OUT output is measured to determine the parameter.
measured to determine the parameter.
with the default settings of T_RX_MOD[7], SDMOD_TYP, DEC_TYP, and COR_F_ENA. The AGC gain is switched to 0 dB.
V
V
Parameter
SN
CLIP_AGC_IN
V
AGC
I
MAX_RX_IN
NF
AGC
LE_RX_IN
REF_OUT
AD_OUT
RX_IN
LPF_OUT
range
step
Input offset voltage 42 dB
Input offset voltage 0 dB
Max. peak input voltage (corresponding to 62.5%
of the SD full scale)
Input referred noise of the analog receiver path
Input leakage current of receiver input
Max. current delivered by REF_OUT
Power supply rejection ratio of the receiver input
section
AGC gain step
AGC range
Analog ground reference output voltage
Signal to noise ratio at 62.5% of the SD full scale
Clipping level at the output of the gain stage
Description
http://onsemi.com
13
Table 14. RECEIVER FREQUENCY
CHARACTERISTICS
Frequency (kHx)
AGC gain = 42 dB
AGC gain = 42 dB
AGC gain = 42 dB
(Notes 16 and 17)
(Notes 16 and 20)
AGC gain = 0 dB
AGC gain = 0 dB
Condition
(Note 16)
1000
2000
130
165
330
660
10
95
(Note 18)
(Note 19)
−300
Min.
0.85
39.9
1.57
1.15
Min. (dB)
5.7
−1
10
35
54
−0.5
−1.3
−4.5
Max.
+300
1.15
44.1
1.73
1.65
150
6.3
50
5
1
Max. (dB)
−18.0
−36.0
−2.0
−3.0
−50
−50
0.5
0.5
NV/#Hz
Unit
mV
mV
mA
mA
Vp
dB
dB
dB
dB
Vp
V