IS42S32400B-7T ISSI, Integrated Silicon Solution Inc, IS42S32400B-7T Datasheet - Page 25
![no-image](/images/manufacturer_photos/0/3/347/issi__integrated_silicon_solution_inc_sml.jpg)
IS42S32400B-7T
Manufacturer Part Number
IS42S32400B-7T
Description
IC SDRAM 128MBIT 143MHZ 86TSOP
Manufacturer
ISSI, Integrated Silicon Solution Inc
Type
SDRAMr
Datasheet
1.IS42S32400B-7T-TR.pdf
(60 pages)
Specifications of IS42S32400B-7T
Format - Memory
RAM
Memory Type
SDRAM
Memory Size
128M (4Mx32)
Speed
143MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Package / Case
86-TSOPII
Organization
4Mx32
Density
128Mb
Address Bus
14b
Access Time (max)
6.5/5.4ns
Maximum Clock Rate
143MHz
Operating Supply Voltage (typ)
3.3V
Package Type
TSOP-II
Operating Temp Range
0C to 70C
Operating Supply Voltage (max)
3.6V
Operating Supply Voltage (min)
3V
Supply Current
130mA
Pin Count
86
Mounting
Surface Mount
Operating Temperature Classification
Commercial
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IS42S32400B-7T
Manufacturer:
ISSI
Quantity:
1 653
Company:
Part Number:
IS42S32400B-7TL
Manufacturer:
ISSI
Quantity:
7 760
Company:
Part Number:
IS42S32400B-7TL
Manufacturer:
ISSI
Quantity:
10
Part Number:
IS42S32400B-7TL
Manufacturer:
ISSI
Quantity:
20 000
Company:
Part Number:
IS42S32400B-7TLI
Manufacturer:
ISSI
Quantity:
2 890
Company:
Part Number:
IS42S32400B-7TLI
Manufacturer:
ISSI
Quantity:
1 080
Part Number:
IS42S32400B-7TLI
Manufacturer:
ISSI
Quantity:
20 000
CAS LATENCY
IS42S32400B
CAS Latency
The CAS latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the
first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and the
latency is m clocks, the data will be available by clock edge
n + m. The DQs will start driving as a result of the clock edge
one cycle earlier (n + m - 1), and provided that the relevant
access times are met, the data will be valid by clock edge
n + m. For example, assuming that the clock cycle time is
such that all relevant access times are met, if a READ
command is registered at T0 and the latency is programmed
to two clocks, the DQs will start driving after T1 and the data
will be valid by T2, as shown in CAS Latency diagrams. The
Allowable Operating Frequency table indicates the operat-
ing frequencies at which each CAS latency setting can be
used.
Reserved states should not be used as unknown operation or
incompatibility with future versions may result.
Integrated Silicon Solution, Inc. — www.issi.com —
PRELIMINARY INFORMATION Rev. 00J
03/03/09
COMMAND
COMMAND
CLK
CLK
DQ
DQ
READ
READ
T0
T0
CAS Latency - 2
NOP
NOP
CAS Latency - 3
T1
T1
1-800-379-4774
t
LZ
t
AC
CAS Latency
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used
because unknown operation or incompatibility with future
versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9 = 1, the
programmed burst length applies to READ bursts, but write
accesses are single-location (nonburst) accesses.
Speed
NOP
NOP
Allowable Operating Frequency (MHz)
T2
T2
-6
-7
D
OUT
t
t
OH
LZ
t
AC
NOP
CAS Latency = 2
T3
T3
D
DON'T CARE
UNDEFINED
OUT
t
OH
125
100
T4
CAS Latency = 3
166
143
25