M27C801-100B1 STMicroelectronics, M27C801-100B1 Datasheet
M27C801-100B1
Specifications of M27C801-100B1
Available stocks
Related parts for M27C801-100B1
M27C801-100B1 Summary of contents
Page 1
... Standby current: 100 µA ■ Programming voltage: 12.75 V ± 0.25 V ■ Programming time: 50 µs/word ■ Electronic signature – Manufacturer code: 20h – Device code: 42h ■ ECOPACK® packages available 8 Mbit (1Mb EPROM and OTP EPROM M27C801 32 1 FDIP32W ( PDIP32 (B) PLCC32 (K) 1/24 1 ...
Page 2
... M27C801 1 Description The M27C801 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable ideally suited for applications where fast turn-around and pattern experimentation are important requirements and is organized as 1,048,576 by 8 bits. The FDIP32W (window ceramic frit-seal package) has transparent lid which allows the user to expose the chip to ultraviolet light to erase the bit pattern ...
Page 3
... Minimum DC voltage on Input or Output is –0.5 V with possible undershoot to –2.0 V for a period less than 20 ns. Maximum DC voltage on Output is V than 20 ns. 12/24 Table 4 may cause permanent damage to Parameter (1) +0.5 V with possible overshoot M27C801 Value Unit –40 to 125 °C –50 to 125 °C –65 to 150 °C – – ...
Page 4
... M27C801 4 DC and AC characteristics This section summarizes the operating and measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristic tables that follow are derived from tests performed under the measurement conditions summarized in the relevant tables. Designers should check that the operating conditions in their circuit match the measurement conditions when relying on the quoted parameters ...
Page 5
... V OUT (1) (2) Parameter Test condition mA MHz OUT > 2 –100 µ ± 10%. CC and removed simultaneously or after V PP +0.5V. CC OUT C L AI01823B Min. Max Min. Max. V ± ±10 OUT – 0.2V 100 –0.3 0 0.4 = –1 mA 3.6 V – 0 M27C801 Unit pF pF Unit ...
Page 6
... M27C801 Table 8. Programming mode DC characteristics Symbol I Input leakage current LI I Supply current CC I Program current PP V Input low voltage IL V Input high voltage IH V Output low voltage OL V Output high voltage TTL voltage ° 6.25V ± 0.25V must be applied simultaneously with or before V ...
Page 7
... Figure 7. Read mode AC waveforms A0-A19 E G Q0-Q7 16/24 (1) (2) Test condition Min ± 10%. CC and removed simultaneously or after V PP VALID tAVQV tGLQV tELQV (3) -55 -80/-90 -100 Max. Min. Max. Min VALID tAXQX tEHQZ tGHQZ Hi-Z AI01583B M27C801 Unit Max. 100 ns 100 ...
Page 8
... M27C801 Table 10. Margin mode AC characteristics Symbol Alt high to V A9HVPH AS9 high to Chip Enable low VPHEL VPS high to Chip Enable high (Set) A10HEH AS10 A10 low to Chip Enable high (Reset) A10LEH AS10 A10 t t Chip Enable transition to V EXA10X AH10 t t Chip Enable transition to V ...
Page 9
... Parameter transition PP and removed simultaneously or after V PP VALID tAVEL DATA IN tQVEL tEHQX tVCHEL tEHVPX tVPHEL tELEH PROGRAM Test condition Min. Max 130 tEHAX DATA OUT tEHQZ tELQV tVPLEL VERIFY AI01270 M27C801 Unit µs µs µs µs ns µs µs µs µs 1 µ ...
Page 10
... M27C801 5 Package mechanical data 5.1 32-pin ceramic frit-seal DIP, with round window (FDIP32WA) Figure 10. FDIP32WA package outline Table 12. FDIP32WA package mechanical data Symbol Ø millimeters Min Typ Max 5.72 0.51 1.40 3.91 4.57 3.89 4.50 0.41 0.56 1.45 0.23 0.30 41.73 42 ...
Page 11
... PDIP-C inches Min Typ 0.015 0.150 0.016 0.045 0.009 1.645 1.500 0.600 0.100 0.600 0.530 0.065 0.120 0° 32 M27C801 Max 0.190 0.021 0.065 0.015 1.665 0.625 0.550 0.087 0.140 15° ...
Page 12
... F = FDIP32W B = PDIP32 K = PLCC32 Temperature range ° – °C 1. High Speed, see For a list of available options (speed, package, etc...) or for further information on any aspect of this device, please contact the nearest STMicroelectronics sales office. 22/24 DC and AC characteristics section for further information. M27C801 - M27C801 ...