PLT.7M-C Panduit Corp, PLT.7M-C Datasheet - Page 134
PLT.7M-C
Manufacturer Part Number
PLT.7M-C
Description
TIE CABLE PAN-TY 18LB 3.1"
Manufacturer
Panduit Corp
Series
PAN-TY®r
Type
Pan-Tyr
Specifications of PLT.7M-C
Wire/cable Tie Type
Standard, Locking
Bundle Diameter
0.68" (17.27mm)
Length
0.258' (78.74mm, 3.10")
Width
0.090" (2.30mm)
Mounting Type
Free Hanging (In-Line)
Tensile Strength
18 lbs. (8.2 kg)
Color
Natural
Cable Tie Length
3.1"
Cable Tie Width
0.09"
Body Material
Nylon 6.6
Tensile Strength Pounds
18lb
Cable Bundle Diameter Min
0.8mm
Cable Bundle Diameter Max
0.68"
Maximum Bundle Diameter
0.68 in
Product
Cable Ties
Application
For indoor use
Height
0.115" (Head)
Protection Class
Tie, Cable
Special Features
Locking
Operating Temp Range
-40C to 85C
Product Length (mm)
79mm
Product Depth (mm)
4.6mm
Product Height (mm)
2.9mm
Accessory Type
Locking Cable Tie
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Features
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
298-1018
light objects to smooth surfaces. These mounts are not designed to support excessive loads and should not
be used when the maximum expected load exceeds the rated capacity of the mount.
proper ratio of resin and hardener are mixed, eliminating wasted epoxy.
PANDUIT
and protecting wires or cables. Some are used with PANDUIT
cable ties. Adhesive backed mounts adhere to a variety of surfaces. This alternative to mechanical fasteners
offers the advantage of lower installed cost with safe, easy to use, quality products.
Applications
• To route wires in control panels and switchboards
• To support bundles of wires away from moving mechanical devices
• Routing and harnessing cables, both indoors and out, to prevent safety hazards
• To organize flat cables in many locations with low profile construction
• Ideal for supporting wire bundles where holes cannot be put into the substrate
•
Markets
• Original Equipment Manufacturers (OEM)
• Construction Industry
• Telecommunication Systems
• CATV
• Aerospace Industry
General Mount Guidelines
PANDUIT
Choosing the Right Adhesive
PANDUIT
wiring accessories products. The general purpose tape is produced with a rubber based adhesive and is
identified by an “-A” in the part number. This tape develops its strength extremely fast and can be used
in environments with temperatures ranging from -20°F to +120°F. It is recommended that rubber based
Acrylic based adhesive tape is also available and is identified by an “-AT” in the part number. This tape is for
use in environments where continuous exposure to temperatures as high as 180°F is possible. Acrylic
PANDUIT
where the surface to which the mount must be applied is porous rather than smooth. This adhesive is
formulated specifically for use on PANDUIT
134
General Introduction
adhesive mounts dwell 2 hours after installation, prior to loading. Rubber based adhesive tape is the best
choice for most adhesive mount applications, including powder coated surfaces.
based adhesive develops its maximum strength over a longer period of time than rubber based adhesive.
It is recommended that acrylic adhesive mounts dwell 8 hours after installation, prior to loading. Acrylic
based adhesive tape is a good choice for environments with prolonged exposure to UV rays or
temperatures above 120°F.
To separate groups of wires for identification
Most commonly used parts appear in BOLD.
®
®
®
®
offers two standard pressure sensitive foam tapes which are available on most adhesive backed
pressure sensitive adhesive (foam tape) mounts are intended to secure wire bundles or other
also offers a two-part epoxy for use in applications where excessive loading is required, or
adhesive mounts provide a quick, economical and dependable method of supporting, routing
Selection and Use of Adhesive Mounts
®
mounts, and is packaged in pre-measured cups to insure the
• Utilities
• Electronic Components
• Transportation Industry
• Appliance Manufacturers
• Maintenance and Repair
Operations (MRO)
®
cable ties and others can be used without