AT24C08A-10PC-2.5 Atmel, AT24C08A-10PC-2.5 Datasheet
AT24C08A-10PC-2.5
Specifications of AT24C08A-10PC-2.5
Related parts for AT24C08A-10PC-2.5
AT24C08A-10PC-2.5 Summary of contents
Page 1
... SCL GND 6 9 SDA 8-Pin PDIP VCC SCL GND 4 5 SDA 8-Pin SOIC VCC SCL GND 4 5 SDA 8-Pin TSSOP VCC SCL GND 4 5 SDA 2-Wire Serial EEPROM 2K (256 (512 (1024 x 8) AT24C02A AT24C04A AT24C08A AT24C02A/04A/ 08A Rev. 0976B–07/98 1 ...
Page 2
... The AT24C04A uses the A2 and A1 inputs for hard wire addressing and a total of four 4K devices may be addressed on a single bus system. The A0 pin con- nect. The AT24C08A only uses the A2 input for hardwire addr total of two ces addressed on a single bus system. The A0 and A1 pins are no connects. ...
Page 3
... Random word addressing requires a 9 bit data word address. Full (8K) Array AT24C08A, 8K SERIAL EEPROM: The 8K is internally organized with 4 blocks of 256 pages of 4-bytes each. Random word addressing requires a 10 bit data word address 1.0 MHz, V ...
Page 4
... STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by follow- ing these steps:(a) Clock cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high ...
Page 5
Bus Timing (SCL: Serial Clock, SDA: Serial Data I/O) Write Cycle Timing (SCL: Serial Clock, SDA: Serial Data I/O) SCL SDA 8th BIT WORD n Note: 1. The write cycle time t WR clear/write cycle. ACK STOP CONDITION is the ...
Page 6
Data Validity Start and Stop Definition Output Acknowledge AT24C02A/04A/08A 6 ...
Page 7
... This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page ...
Page 8
... As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word Figure 1. Device Address Figure 2. Byte Write SDA LINE Figure 3. Page write ...
Page 9
Figure 4. Current Address Read SDA LINE Figure 5. Random Read DEVICE T ADDRESS SDA LINE Figure 6. Sequential Read DEVICE T D ADDRESS M L ...
Page 10
AT24C02A Ordering Information t (max) I (max) I (max (ms) (µA) (µA) 10 3000 18 3000 18 10 1500 4 1500 4 10 1000 4 1000 4 10 800 3 800 3 8P3 8-Lead, 0.300" Wide, Plastic ...
Page 11
AT24C04A Ordering Information t (max) I (max) I (max (ms) (µA) (µA) 10 3000 18 3000 18 10 1500 4 1500 4 10 1000 4 1000 4 10 800 3 800 3 8P3 8-Lead, 0.300" Wide, Plastic ...
Page 12
... AT24C08A-10PC AT24C08AN-10SC AT24C08A-10SC AT24C08A-10TC 400 AT24C08A-10PI AT24C08AN-10SI AT24C08A-10SI AT24C08A-10TI 100 AT24C08A-10PC-2.7 AT24C08AN-10SC-2.7 AT24C08A-10SC-2.7 AT24C08A-10TC-2.7 100 AT24C08A-10PI-2.7 AT24C08AN-10SI-2.7 AT24C08A-10SI-2.7 AT24C08A-10TI-2.7 100 AT24C08A-10PC-2.5 AT24C08AN-10SC-2.5 AT24C08A-10SC-2.5 AT24C08A-10TC-2.5 100 AT24C08A-10PI-2.5 AT24C08AN-10SI-2.5 AT24C08A-10SI-2.5 AT24C08A-10TI-2.5 100 AT24C08A-10PC-1.8 AT24C08AN-10SC-1.8 AT24C08A-10SC-1.8 AT24C08A-10TC-1.8 100 AT24C08A-10PI-1.8 AT24C08AN-10SI-1.8 AT24C08A-10SI-1.8 AT24C08A-10TI-1.8 Package Type ...
Page 13
Packaging Information 8P3, 8-Lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) Dimensions in Inches and (Millimeters) JEDEC STANDARD MS-001 BA .400 (10.16) .355 (9.02) PIN 1 .300 (7.62) REF .210 (5.33) MAX .100 (2.54) BSC SEATING PLANE .150 (3.81) .115 ...
Page 14
AT24C02A/04A/08A 14 ...
Page 15
15 ...
Page 16
... No licenses to patents or other intellectual prop Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life suppor t devices or systems. ...