AT27C080-15TI Atmel, AT27C080-15TI Datasheet
AT27C080-15TI
Specifications of AT27C080-15TI
Related parts for AT27C080-15TI
AT27C080-15TI Summary of contents
Page 1
... The AT27C080 chip is a low-power, high-performance 8,388,608-bit one-time pro- grammable read only memory (OTP EPROM) organized bits. The AT27C080 requires only one 5V power supply in normal read mode operation. Any byte can be accessed in less than 90 ns, eliminating the need for speed reducing WAIT states on high-performance microprocessor systems. Atmel’ ...
Page 2
... 2.2 32-lead PDIP Top View A19 1 32 A16 2 31 A15 3 30 A12 GND 16 17 AT27C080 2 Function Addresses Outputs Chip Enable Output Enable/Program Supply 2.3 OE/VPP 32 31 A10 GND VCC A18 A17 A14 A13 A8 A9 A11 OE/VPP A10 32-lead PLCC Top View ...
Page 3
... This is a stress rating only and functional operation of the device at these or any other conditions beyond those (1) indicated in the operational sections of this specification is not implied. Exposure to abso- lute maximum rating conditions for extended (1) periods may affect device reliability. (1) 2 AT27C080 3 ...
Page 4
... OE Outputs Ai D OUT (1) X High Z X High OUT X High Z ( Identification Code A19 = V IL and A0 which is toggled H AT27C080-90 -40° 85° ± 10% Min Max Units ±1.0 ±5.0 100 1.0 40 -0.6 0.8 2 0.5 CC 0.4 2 0360L–EPROM–12/07 µA µA µ ...
Page 5
... Condition whichever occurred first PP (1) or CE, whichever occurs first. Output float is defined as the point when data is no longer driven after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C080-90 Min CE. . ACC AT27C080 Max Units ...
Page 6
... F 12. Output Test Load Note: 13. Pin Capacitance ( MHz 25° C Symbol Typ OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. AT27C080 6 1.3V (1N914) 3.3K OUTPUT PIN 100 pF including jig capacitance. Max 8 12 Units Conditions pF V ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 0360L–EPROM–12/07 and 2.0V for AT27C080 7 ...
Page 8
... CC 2. This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 50 µs ± 5%. 17. Atmel’s AT27C080 Integrated Product Identification Code Codes A0 O7 Manufacturer ...
Page 9
... OE/V are read again and compared with the original data to determine if the device passes or fails. 0360L–EPROM–12/07 is raised to 13.0V. Each address is first programmed with one PP is then lowered AT27C080 is CC and V to 5.0V. All bytes IL CC ...
Page 10
... Plastic Thin Small Outline Package (TSOP) AT27C080 10 Ordering Code Package AT27C080-90JI 32J AT27C080-90PI 32P6 AT27C080-90TI 32T Ordering Code Package AT27C080-90JU 32J AT27C080-90PU 32P6 AT27C080-90TU 32T Package Type Operation Range Industrial (-40° 85° C) Operation Range Industrial (-40° 85° C) 0360L–EPROM–12/07 ...
Page 11
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0360L–EPROM–12/07 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 32J, 32-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C080 0.318(0.0125) 0.191(0.0075 COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 3.175 – ...
Page 12
... PDIP A SEATING PLANE Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R AT27C080 12 D PIN 0º ~ 15º REF eB TITLE 32P6, 32-lead (0.600"/15.24 mm Wide) Plastic Dual ...
Page 13
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0360L–EPROM–12/07 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT27C080 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 14
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...