AT27C1024-15PI Atmel, AT27C1024-15PI Datasheet
AT27C1024-15PI
Specifications of AT27C1024-15PI
Available stocks
Related parts for AT27C1024-15PI
AT27C1024-15PI Summary of contents
Page 1
... PDIP, PLCC, and VSOP packages. The device features two-line control (CE, OE) to eliminate bus contention in high-speed systems. With high density 64K word storage capability, the AT27C1024 allows firmware to be stored reliably and to be accessed by the system without the delays of mass storage media. Atmel’ ...
Page 2
... VSOP Top View – Type A10 2 A11 3 A12 4 A13 5 A14 6 A15 PGM 9 VCC 10 VPP O15 13 O14 14 O13 15 O12 16 O11 17 O10 AT27C1024 2 Function Addresses Outputs Chip Enable Output Enable Program Strobe No Connect 2.3 VCC PGM NC A15 A14 A13 A12 A11 A10 A9 GND GND ...
Page 3
... This is a stress rating only and functional operation of the device at these or any other condi- tions beyond those indicated in the operational sec- (1) tions of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. (1) (1) AT27C1024 3 ...
Page 4
... ( ( Identification Code except A9 which is set to V and A0 which is toggled select the Device Code word AT27C1024 -70 -40° 85° ± 10% Min Max Ind. ±1 Auto. ±5 Ind. ±5 Auto. ±10 10 100 -0.6 0.8 2 0.5 CC 0.4 2 0019M–EPROM–12/07 Outputs D OUT High Z ...
Page 5
... Output float is defined as the point when data is no longer driven. 0019M–EPROM–12/07 Condition (1) = 0.8V and after the falling edge of CE without impact after the address is valid without impact on t ACC OE AT27C1024 AT27C1024 -45 -70 Min Max Min Max 0.0V and V = 3.0V. Timing measure ...
Page 6
... Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. 12. Input Test Waveforms and Measurement Levels For -45 devices only: For -70 devices only: 13. Output Test Load Note 100 pF including jig capacitance except -45 devices, where C L AT27C1024 6 Max < (10% to 90%) R ...
Page 7
... Programming Waveforms Notes: 1. The Input Timing Reference is 0.8V for and t are characteristics of the device but must be accommodated by the programmer. OE DFP 3. When programming the AT27C1024 a 0.1 µF capacitor is required across V transients. 15. DC Programming Characteristics ± 5° 6.5 ± 0.25V Symbol Parameter I Input Load Current ...
Page 8
... This parameter is only sampled and is not 100% tested. Output Float is defined as the point where data is no longer driven – see timing diagram. 3. Program Pulse width tolerance is 100 17. Atmel’s AT27C1024 Integrated Product Identification Code Codes A0 Manufacturer 0 Device Type ...
Page 9
... V are read again and compared with the original data to determine if the device passes or fails. 0019M–EPROM–12/07 is raised to 13.0V. Each address is first programmed with one 100 µ then lowered to 5.0V and V PP AT27C1024 5.0V. All words CC 9 ...
Page 10
... Ordering Code Package AT27C1024-45JI 44J AT27C1024-45PI 40P6 AT27C1024-45VI 40V AT27C1024-70JI 44J AT27C1024-70PI 40P6 AT27C1024-70VI 40V Ordering Code Package AT27C1024-45JU 44J AT27C1024-45PU 40P6 AT27C1024-70JU 44J AT27C1024-70PU 40P6 Package Type Operation Range Industrial (-40° 85° C) (1) Industrial (-40° 85° C) (1) Operation Range Industrial (-40° ...
Page 11
... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0019M–EPROM–12/07 1.14(0.045) X 45˚ PIN NO. 1 IDENTIFIER TITLE 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) AT27C1024 0.318(0.0125) 0.191(0.0075) D2/ COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 4.191 – ...
Page 12
... PDIP A SEATING PLANE Notes: 1. This package conforms to JEDEC reference MS-011, Variation AC. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R AT27C1024 12 D PIN 0º ~ 15º REF eB TITLE 40P6, 40-lead (0.600" ...
Page 13
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0019M–EPROM–12/07 PIN SEATING PLANE A1 TITLE 40V, 40-lead ( Package) Plastic Thin Small Outline Package, Type I (VSOP) AT27C1024 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 14
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...