AT29C512-90JC Atmel, AT29C512-90JC Datasheet
![IC FLASH 512KBIT 90NS 32PLCC](/photos/7/21/72190/453-32-plcc_sml.jpg)
AT29C512-90JC
Specifications of AT29C512-90JC
Available stocks
Related parts for AT29C512-90JC
AT29C512-90JC Summary of contents
Page 1
... Five-volt-only commands determine the operation of the device. Reading data out of the device is similar to reading from an EPROM. Reprogramming the AT29C512 is performed on a sector basis; 128 bytes of data are loaded into the device and then simultaneously programmed. During a reprogram cycle, the address locations and 128 bytes of data are internally latched, freeing the address and data bus for other operations ...
Page 2
... Pin Configurations Pin Name A0 - A15 I/O0 - I/O7 NC 2.1 32-lead PLCC Top View 2.2 32-lead TSOP (Type 1) Top View AT29C512 2 Function Addresses Chip Enable Output Enable Write Enable Data Inputs/Outputs No Connect I/ A11 A13 4 A14 VCC A15 11 A12 A14 A13 A8 A9 A11 OE A10 ...
Page 3
... Device Operation 4.1 Read The AT29C512 is accessed like an EPROM. When CE and OE are low and WE is high, the data stored at the memory location determined by the address pins is asserted on the outputs. The outputs are put in the high impedance state whenever high. This dual-line control gives designers flexibility in preventing bus contention ...
Page 4
... Software Data Protection A software controlled data protection feature is available on the AT29C512. Once the software protection is enabled a software algorithm must be issued to the device before a program may be performed. The software protection feature may be enabled or disabled by the user; when shipped from Atmel, the software data protection feature is disabled. To enable the software data protection, a series of three program commands to specific addresses with specific data must be performed ...
Page 5
... DATA Polling The AT29C512 features DATA polling to indicate the end of a program cycle. During a program cycle an attempted read of the last byte loaded will result in the complement of the loaded data on I/O7. Once the program cycle has been completed, true data is valid on all outputs and the next cycle may begin ...
Page 6
... A15 = A1-A15 = V Condition MHz OUT -400 µ -100 µ 4. AT29C512-70 AT29C512-90 -40C - 85C -40C - 85C 5V± 5% 5V± Manufacturer Code ( Device Code Manufacturer Code Device Code IH Min Max 10 10 300 3 50 0.8 2.0 0.45 2.4 4.2 I/O ...
Page 7
... whichever occurs first ( pF This parameter is characterized and is not 100% tested. 0456i–FLASH–9/08 AT29C512-70 Min (1)(2)(3)( after the address transition without impact on t ACC after the falling edge of CE without impact AT29C512 AT29C512-90 Max Min Max ACC after an address change ...
Page 8
... Input Test Waveforms and Measurement Level t R 12. Output Test Load 13. Pin Capacitance ( MHz 25°C Symbol Typ OUT Note: 1. This parameter is characterized and is not 100% tested. AT29C512 < 5.0V 1.8K OUTPUT PIN 30pF 1.3K Max 6 12 90/120/150 ns 5.0V 1.8K OUTPUT PIN 100pF 1.3K ...
Page 9
... Data Set-up Time Data, OE Hold Time DH OEH t Write Pulse Width High WPH 15. AC Byte Load Waveforms 15.1 WE Controlled OE ADDRESS CE WE DATA IN 15.2 CE Controlled OE ADDRESS WE CE DATA IN 0456i–FLASH–9/ OES OEH OES t OEH AT29C512 Min Max 100 t WPH WPH t DH Units ...
Page 10
... A0-A6 A7-A5 Notes through A15 must specify the sector address during each high-to-low transition of WE (or CE must be high when WE and CE are both low. 3. All bytes that are not loaded within the sector being programmed will be indeterminate. AT29C512 10 Min 100 (1)(2)(3) Max ...
Page 11
... WPH BYTE ADDRESS 5555 2AAA 5555 SECTOR ADDRESS BYTE 0 AT29C512 (1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 80 TO ADDRESS 5555 LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA 20 TO ADDRESS 5555 ...
Page 12
... AC Read Characteristics. OE 24. Toggle Bit Waveforms (2) I/O6 Notes: 1. Toggling either both OE and CE will operate toggle bit. 2. Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. AT29C512 12 (1) (1) (1)(2)(3) t OEH HIGH Z ...
Page 13
... ADDRESS 2AAA LOAD DATA 90 TO ADDRESS 5555 PAUSE 10 mS ENTER PRODUCT IDENTIFICATION (2)(3)(5) MODE (1) LOAD DATA AA TO ADDRESS 5555 LOAD DATA 55 TO ADDRESS 2AAA LOAD DATA F0 TO ADDRESS 5555 PAUSE 10 mS EXIT PRODUCT IDENTIFICATION (4) MODE ; Device Code is read for AT29C512 . IH 13 ...
Page 14
... Normalized I Graphs CC AT29C512 14 NORMALI ED SUPPLY CURRENT vs. TEMPERATURE 1 0.8 -55 - TEMPERATURE (C) NORMALI ED SUPPLY CURRENT vs. ADDRESS FREQUENCY 25C FREQUENCY (MHz) NORMALI ED SUPPLY CURRENT vs. SUPPLY VOLTAGE 0.6 4.50 4.75 5.00 SUPPLY VOLTAGE ( 125 5.25 5.50 0456i–FLASH–9/08 ...
Page 15
... Active Standby 0.3 32J 32-lead, Plastic J-leaded Chip Carrier (PLCC) 32T 32-lead, Thin Small Outline Package (TSOP) 0456i–FLASH–9/08 Ordering Code AT29C512-70JU AT29C512-70TU AT29C512-90JU AT29C512-90TU Package Type AT29C512 Package Operation Range 32J 32T Industrial (-40 to 85C) 32J 32T 15 ...
Page 16
... Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010 (0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004 (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R AT29C512 16 1.14(0.045 PIN NO. 1 IDENTIFIER ...
Page 17
... Lead coplanarity is 0.10 mm maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0456i–FLASH–9/08 PIN SEATING PLANE A1 TITLE 32T, 32-lead ( Package) Plastic Thin Small Outline Package, Type I (TSOP) AT29C512 0º ~ 8º GAGE PLANE COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL MIN NOM MAX A – – ...
Page 18
... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...