M24C04-WMN6P STMicroelectronics, M24C04-WMN6P Datasheet - Page 17

• Manufacturer Part Number: M24C04-WMN6P
• Description: IC EEPROM 4KBIT 400KHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M24C04-WMN6P

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 4K (512 x 8)
• Speed: 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Organization: 512 x 8
• Interface Type: I2C
• Maximum Clock Frequency: 0.4 MHz
• Access Time: 900 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 2 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 5.5 V
• Capacitance, Input: 8 pF (SDA), 6 pF (Other Pins)
• Current, Input, Leakage: ±2 μA
• Current, Operating: 2 mA
• Current, Output, Leakage: ±2
• Current, Supply: 3 mA
• Data Retention: >40 yrs.
• Density: 4K
• Package Type: SO8
• Temperature, Operating: -40 to +85 °C
• Temperature, Operating, Maximum: 85 °C
• Temperature, Operating, Minimum: -40 °C
• Time, Access: 900 ns
• Time, Fall: 50 ns
• Time, Rise: 50 ns
• Voltage, Esd: 4000 V
• Voltage, Input, High: 3.5 to 6.5 V
• Voltage, Input, High Level: 0.7 V
• Voltage, Input, Low: 0.75 to 1.65 V
• Voltage, Input, Low Level: –0.45 V
• Voltage, Output, Low: 0.4 V
• Voltage, Supply: 2.5 to 5.5 V
• Memory Configuration: 512 X 8
• Clock Frequency: 400kHz
• Supply Voltage Range: 2.5V To 5.5V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8562; M24C04-WMN6P

M24C16, M24C08, M24C04, M24C02, M24C01
3.7.2
3.7.3
3.7.4
Current Address Read
For the Current Address Read operation, following a Start condition, the bus master only
sends a device select code with the Read/Write bit (RW) set to 1. The device acknowledges
this, and outputs the byte addressed by the internal address counter. The counter is then
incremented. The bus master terminates the transfer with a Stop condition, as shown in
Figure
Sequential Read
This operation can be used after a Current Address Read or a Random Address Read. The
bus master does acknowledge the data byte output, and sends additional clock pulses so
that the device continues to output the next byte in sequence. To terminate the stream of
bytes, the bus master must not acknowledge the last byte, and must generate a Stop
condition, as shown in
The output data comes from consecutive addresses, with the internal address counter
automatically incremented after each byte output. After the last memory address, the
address counter ‘rolls-over’, and the device continues to output data from memory address
00h.
Acknowledge in Read mode
For all Read commands, the device waits, after each byte read, for an acknowledgment
during the 9
time, the device terminates the data transfer and switches to its Standby mode.
10, without acknowledging the byte.
th
bit time. If the bus master does not drive Serial Data (SDA) Low during this
Figure
10.
Doc ID 5067 Rev 16
Device operation
17/39