EPC1213PI8 Altera, EPC1213PI8 Datasheet - Page 17

• Manufacturer Part Number: EPC1213PI8
• Description: IC CONFIG DEVICE 212KBIT 8-DIP
• Manufacturer: Altera
• Series: EPCr

Specifications of EPC1213PI8

• Programmable Type: OTP
• Memory Size: 212kb
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• For Use With: PLMJ1213 - PROGRAMMER ADAPTER 20 PIN J-LEAD
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 544-1370-5; EPC1213PI8

Chapter 4: Configuration Devices for SRAM-Based LUT Devices Data Sheet
Timing Information
Table 4–9. Timing Parameters when Using EPC1 and EPC1441 Devices at 3.3 V
Table 4–10. Timing Parameters when Using EPC1, EPC2 and EPC1441 Devices at 5.0 V (Part 1 of 2)
© December 2009
t
t
t
t
t
t
t
f
t
t
t
t
t
t
t
t
t
Note to
(1) During initial power-up, a POR delay occurs to permit voltage levels to stabilize. Subsequent reconfigurations do not incur this delay.
t
t
t
t
t
t
t
f
t
t
POR
OEZX
CE
DSU
DH
CO
CDOE
CLK
MCH
MCL
SCH
SCL
CASC
CCA
OEW
OEC
NRCAS
POR
OEZX
CE
DSU
DH
CO
CDOE
CLK
MCH
MCL
Symbol
Symbol
Table
4–9:
POR delay
OE high to DATA output enabled
OE high to first rising edge on DCLK
Data setup time before rising edge on DCLK
Data hold time after rising edge on DCLK
DCLK to DATA out
DCLK to DATA enable/disable
DCLK frequency
DCLK high time for the first device in the configuration
chain
DCLK low time for the first device in the configuration
chain
POR delay
OE high to DATA output enabled
OE high to first rising edge on DCLK
Data setup time before rising edge on DCLK
Data hold time after rising edge on DCLK
DCLK to DATA out
DCLK to DATA enable/disable
DCLK frequency
DCLK high time for the first device in the configuration
chain
DCLK low time for the first device in the configuration
chain
DCLK high time for subsequent devices
DCLK low time for subsequent devices
DCLK rising edge to nCASC
nCS to nCASC cascade delay
OE low pulse width (reset) to guarantee counter reset
OE low (reset) to DCLK disable delay
OE low (reset) to nCASC delay
Altera Corporation
Table 4–9
3.3 V.
Table 4–10
devices at 5.0 V.
(1)
(1)
defines the timing parameters when using EPC1 and EPC1441 devices at
Parameter
defines the timing parameters when using EPC1, EPC2, and EPC1441
Parameter
Min
100
—
—
—
30
—
—
50
50
50
50
—
—
—
—
0
2
Min
6.7
—
—
—
30
—
—
30
30
0
Configuration Handbook (Complete Two-Volume Set)
125
125
Typ
—
—
—
—
—
—
—
—
—
—
—
—
—
—
4
Typ
—
—
—
—
—
—
—
10
50
50
Max
200
300
250
250
80
—
—
30
30
10
—
—
25
15
—
30
30
Max
16.7
200
200
50
—
—
20
20
75
75
Units
Units
MHz
MHz
ms
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ns
ns
ns
ns
ns
ns
ns
ns
4–17