NCP1205P ON Semiconductor, NCP1205P Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
NCP1205P
Manufacturer Part Number
NCP1205P
Description
IC CTRLR PWM CM OVP UVLO HV 8DIP
Manufacturer
ON Semiconductor
Datasheet
1.NCP1205DR2.pdf
(17 pages)
Specifications of NCP1205P
Output Isolation
Isolated
Frequency Range
90 ~ 125kHz
Voltage - Input
8 ~ 36 V
Voltage - Output
12V
Operating Temperature
-25°C ~ 150°C
Package / Case
8-DIP (0.300", 7.62mm)
Number Of Outputs
1
Output Current
250 mA
Mounting Style
Through Hole
Switching Frequency
125 KHz
Operating Supply Voltage
30 V
Maximum Operating Temperature
+ 125 C
Fall Time
30 ns
Minimum Operating Temperature
- 25 C
Rise Time
30 ns
Synchronous Pin
No
Topology
Flyback, Forward
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
NCP1205POS
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NCP1205P
Manufacturer:
TEXAS
Quantity:
65
Part Number:
NCP1205P
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1205P2G
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
NCP1205PG
Manufacturer:
ON/安森美
Quantity:
20 000
back within its regulation area, the IC operation comes back
to normal.
8 x 128 ms delay is combined with the previous 128 ms. It
works as follows: the 128 ms delay is provided to account for
any normal transients that engender a temporary loss of
feedback (FB goes toward ground). However, when the
128 ms period is actually over (the feedback is definitively
lost) the IC stops the output driving pulses for a typical
period of 8 x 128 ms. During this mode, the rest of the
functions are still activated. For instance, in lack of pulses,
the self- -supplied being no longer provided, the startup
source turns on and off (when reaching the corresponding
UVLO
on the Vcc line. As soon as the feedback condition is
restored, the 8 x 128 ms is interrupted and, in synchronism
with the Vcc line, the IC is back to normal. The following
diagrams show how this mechanism takes place when FB is
down to zero (optocoupler opened) or up to Vcc
(optocoupler shorted). If we assume that the error is
permanently present, then a burst mode takes place with a
128/8 x 128 = 12.5% duty- -cycle. The real transmitted
power is thus:
As soon as the system recovers from the error, e.g. FB is
To avoid any system thermal runaway, another internal
Pout BURST = 1
L
and UVLO
H
2
levels), creating an hiccup waveform
· Lp · Ip 2 · Fsw · Duty BURST
http://onsemi.com
14
Overvoltage Detection (OVP)
allows to shutdown the controller as soon as the level on this
pin exceeds 2.8V, as detailed in Figure 16. In lack of
switching pulses, the Vcc capacitor is no longer refreshed by
the auxiliary supply and slowly discharges toward ground.
When the Vcc level crosses UVLOL, a new startup sequence
occurs. If the OVP has gone, the converter resumes its
operation.
Protecting Pin 1 Against Negative Spikes
negative voltages that could appear on it’s pins. To avoid any
adverse latch- -up of the IC, we strongly recommend
inserting a 15 k resistor in series with pin 1 and the
high- -voltage rail, as shown in Figures 17 and 18. This 15 k
resistor prevents from adversely latching the controller in
case of negative spikes appearing on the bulk capacitor
during the power- -off sequence. Please note that this resistor
does not dissipate any continuous power and can therefore
be of low power type. Two 8.2 k can also be wired in series
to sustain the large DC voltage present on the bulk.
Latched
OVP
Figure 16. In the PDIP- -8 Version, the OVP Pad is not
On the PDIP- -14 and the SOIC- -16 versions, an OVP pin
As any CMOS controller, NCP1205 is sensitive to
Pinned Out and is Available with PDIP- -14 Devices
2
+
--
7
1
Only
+
2.8 V
18 k
2 k
8
OVP