DS2786G+ Maxim Integrated Products, DS2786G+ Datasheet - Page 9
![IC FUEL GAUGE OCV 10-TDFN](/photos/7/34/73439/10-tdfn_pkg_21-0268_sml.jpg)
DS2786G+
Manufacturer Part Number
DS2786G+
Description
IC FUEL GAUGE OCV 10-TDFN
Manufacturer
Maxim Integrated Products
Datasheet
1.DS2786G.pdf
(22 pages)
Specifications of DS2786G+
Function
Fuel, Gas Gauge/Monitor
Battery Type
Lithium-Ion (Li-Ion), Lithium-Polymer (Li-Pol)
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-TDFN Exposed Pad
Operating Supply Voltage
2.5 V to 5.5 V
Supply Current
50 uA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Charge Safety Timers
No
Mounting Style
SMD/SMT
Temperature Monitoring
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
TEMPERATURE MEASUREMENT
The DS2786 uses an integrated temperature sensor to measure battery temperature with a resolution of 0.125°C.
Temperature measurements are updated every 1760ms and placed in the Temperature Register in two’s
complement form. The format of the Temperature Register is shown in Figure 7. The ITEMP bit in the
Status/Configuration Register must be set to enable the internal temperature measurement instead of the AIN1
measurement.
Figure 7. Temperature Register Format
CURRENT MEASUREMENT
In the Active mode of operation, the DS2786 continually measures the current flow into and out of the battery by
measuring the voltage drop across a low-value current-sense resistor, R
pins. The voltage sense range between SNS and V
V
to 102mV are allowed at the input as long as the continuous or average signal level does not exceed ±51.2mV over
the conversion cycle period. The ADC samples the input differentially and updates the Current Register every
880ms at the completion of each conversion cycle. Figure 8 describes the Current Measurement Register format
and resolution for each option. Charge currents above the maximum register value are reported at the maximum
value (7FFFh = +51.2mV). Discharge currents below the minimum register value are reported at the minimum
value (8000h = -51.2mV).
Every 1024th conversion, the ADC measures its input offset to facilitate offset correction to improve Current
accuracy. Offset correction occurs approximately every 15 minutes. The resulting correction factor is applied to the
subsequent 1023 measurements. During the offset correction conversion, the ADC does not make a measurement.
The current measurement just prior to the offset conversion is displayed in the Current Register.
Figure 8. Current Register Formats
SNS
is less than V
MSb
“S”: sign bit(s), “X”: reserved
MSb
“S”: sign bit
S
S
2
2
10
9
SS
MSB—Address 0Eh
MSB—Address 0Ah
, and negative current values occur when V
2
2
8
9
2
2
7
8
2
2
6
7
2
2
5
6
2
2
4
5
LSb
LSb
2
2
3
4
SS
9 of 22
is ±51.2mV. Note that positive current values occur when
MSb
MSb
2
2
2
3
SNS
2
is greater than V
2
DS2786 Stand-Alone OCV-Based Fuel Gauge
1
2
LSB—Address 0Fh
LSB—Address 0Bh
SNS
2
2
0
1
, connected between the SNS and V
2
X
0
SS
X
X
. Peak signal amplitudes up
Units: 25V/R
Units: 0.125C
X
X
X
X
LSb
LSb
X
X
SNS
SS