LT3092EST#TRPBF Linear Technology, LT3092EST#TRPBF Datasheet - Page 8
![IC PROG CURRENT SOURCE SOT223-3](/photos/7/35/73514/sot-223-3_05-08-1630_sml.jpg)
LT3092EST#TRPBF
Manufacturer Part Number
LT3092EST#TRPBF
Description
IC PROG CURRENT SOURCE SOT223-3
Manufacturer
Linear Technology
Datasheet
1.LT3092ETS8TRMPBF.pdf
(22 pages)
Specifications of LT3092EST#TRPBF
Function
Current Source
Accuracy
±1%
Voltage - Input
1.2 ~ 40 V
Current - Output
200mA
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
SOT-223 (3 leads + Tab), SC-73, TO-261
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Sensing Method
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LT3092
APPLICATIONS INFORMATION
Introduction
The LT3092 is a versatile IC that operates as a 2-terminal
programmable current source with the addition of only
two external resistors; no external bypass capacitors are
needed for stability.
The LT3092 is easy to use and has all the protection fea-
tures expected in high performance products. Included
are reverse-voltage protection, reverse-current protec-
tion, short-circuit protection and thermal shutdown with
hysteresis.
The LT3092 operates with or without input and output
capacitors. The simplest current source application
requires only two discrete resistors to set a constant
output current up to 200mA. A variety of analog tech-
niques lend themselves to regulating and varying the
current source value.
The device utilizes a precision “0” TC 10μA reference cur-
rent source to program output current. This 10μA current
source connects to the noninverting input of a power
operational amplifi er. The power operational amplifi er
provides a low impedance buffered output of the voltage
on the noninverting input.
Many application areas exist in which operation without
input and output capacitors is advantageous. A few of
these applications include sensitive circuits that cannot
endure surge currents under fault or overload conditions
and intrinsic safety applications in which safety regulations
limit energy storage devices that may spark or arc.
Programming Output Current in 2-Terminal
Current Source Mode
Setting the LT3092 to operate as a 2-terminal current
source is a simple matter. The 10μA reference current from
the SET pin is used with one resistor to generate a small
voltage, usually in the range of 100mV to 1V (200mV is
a level that will help reject offset voltage, line regulation,
and other errors without being excessively large). This
voltage is then applied across a second resistor that
connects from OUT to the fi rst resistor. Figure 1 shows
connections and formulas to calculate a basic current
source confi guration.
8
With a 10μA current source generating the reference that
gains up to set output current, leakage paths to or from
the SET pin can create errors in the reference and output
currents. High quality insulation should be used (e.g.,
Tefl on, Kel-F). The cleaning of all insulating surfaces to
remove fl uxes and other residues may be required. Surface
coating may be necessary to provide a moisture barrier
in high humidity environments.
Minimize board leakage by encircling the SET pin and
circuitry with a guard ring operated at a potential close
to itself; tie the guard ring to the OUT pin. Guarding
both sides of the circuit board is required. Bulk leakage
reduction depends on the guard ring width. Ten nano-
amperes of leakage into or out of the SET pin and its as-
sociated circuitry creates a 0.1% reference current error.
Leakages of this magnitude, coupled with other sources
of leakage, can cause signifi cant offset voltage and refer-
ence current drift, especially over the possible operating
temperature range.
Selecting R
In Figure 1, both resistors R
value of the output current. The question now arises: the
ratio of these resistors is known, but what value should
each resistor be?
The fi rst resistor to select is R
generate enough voltage to minimize the error caused by
the offset between the SET and OUT pins. A reasonable
starting level is 200mV of voltage across R
to 20k). Resultant errors due to offset voltage are a few
percent. The lower the voltage across R
higher the error term due to the offset.
V
SET
Figure 1. Using the LT3092 as a Current Source
LT3092
+
–
SET
R
SET
SET
10μA
and R
+
–
IN
I
OUT
OUT
OUT
R
OUT
SET
SET
3092 F01
. The value selected should
I
I
V
OUT
OUT
SET
and R
≥
=
=
0 5
R
10
V
.
SET
OUT
µA R
mA
SET
OUT
=
•
SET
10
SET
becomes, the
program the
µA
R
(R
OUT
• R R
SET
SET
equal
3092fb