AS1107WL-T austriamicrosystems, AS1107WL-T Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/0/84/austriamicrosystems_sml.jpg)
AS1107WL-T
Manufacturer Part Number
AS1107WL-T
Description
IC LED 8-DIGIT DRIVER 24-SOIC
Manufacturer
austriamicrosystems
Datasheet
1.AS1107WL-T.pdf
(21 pages)
Specifications of AS1107WL-T
Display Type
LED
Configuration
7 Segment + DP
Interface
Serial
Digits Or Characters
8 Digits
Current - Supply
330mA
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (0.300", 7.50mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
AS1107WL-TTR
AS1106, AS1107
Datasheet - P i n A s s i g n m e n t s
4 Pin Assignments
Figure 2. DIP and SO Pin Assignments (Top View)
4.1 Pin Descriptions
www.austriamicrosystems.com/LED-Driver-ICs/AS1106_07
Table 1. Pin Descriptions
2, 3, 5, 6, 7, 8, 10,
14, 15, 16, 17, 20,
Pin Number
21, 22, 23
4, 9
11
12
13
18
19
24
1
SEG A:SEG G, SEG DP
DIG 0:DIG 7
LOAD/CSN
Pin Name
DOUT
GND
ISET
VDD
CLK
DIN
Serial-Data Input. Data is loaded into the internal 16-bit shift register on the rising edge of
pin CLK.
Digit Drive Lines. 8 Eight-digit drive lines that sink current from the display common
cathode. The AS1106 pulls the digit outputs to V
are high-impedance when turned off.
Ground. Both GND pins must be connected.
Load-Data Input (AS1106 only). The last 16 bits of serial data are latched on the rising edge
of this pin.
Chip-Select Input (AS1107 or AS1106 SPI-enabled only). Serial data is loaded into the shift
register while this pin is low. The last 16 bits of serial data are latched on the rising edge of
this pin.
Serial-Clock Input. 10MHz maximum rate. Data is shifted into the internal shift register on
the rising edge of this pin. Data is clocked out of pin DOUT on the falling edge of this pin. On
the AS1107 or AS1106 SPI-enabled, the CLK input is active only while LOAD/CSN is low.
Seven Segment and Decimal Point Drive Lines. 8 seven-segment drives and decimal
point drive that source current to the display. On the AS1106, when a segment driver is
turned off it is pulled to GND. The AS1107 segment drivers are high-impedance when turned
off.
Set Segment Current. Connect to V
Selecting RSET Resistor Value and Using External Drivers on page
Positive Supply Voltage. Connect to +2.7 to +5.5V supply.
Serial-Data Output. The data into pin DIN is valid at pin DOUT 16.5 clock cycles later. This
pin is used to daisy-chain several AS1106/AS1107 devices and is never high-impedance.
LOAD/CSN
DIG 0
DIG 4
DIG 6
DIG 2
DIG 3
DIG 7
DIG 5
DIG 1
GND
GND
DIN
10
11
12
1
2
3
4
5
6
7
8
9
Revision 2.28
24
23
22
21
20
19
18
17
16
15
14
13
DOUT
SEG D
SEG DP
SEG E
SEG C
VDD
ISET
SEG G
SEG B
SEG F
SEG A
CLK
DD
Description
through R
DD
SET
when turned off. The AS1107 digit drivers
to set the peak segment current (see
14).
2 - 21