AS1106WE austriamicrosystems, AS1106WE Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/0/84/austriamicrosystems_sml.jpg)
AS1106WE
Manufacturer Part Number
AS1106WE
Description
IC LED 8-DIGIT DRIVER 24-SOIC
Manufacturer
austriamicrosystems
Datasheet
1.AS1107WL-T.pdf
(21 pages)
Specifications of AS1106WE
Display Type
LED
Configuration
7 Segment + DP
Interface
Serial
Digits Or Characters
8 Digits
Current - Supply
330mA
Voltage - Supply
2.7 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SOIC (0.300", 7.50mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AS1106WE
Manufacturer:
austriamicrosystems
Quantity:
135
Part Number:
AS1106WE
Manufacturer:
AMS
Quantity:
20 000
Part Number:
AS1106WE-T
Manufacturer:
AMS
Quantity:
20 000
AS1106, AS1107
Datasheet - D e t a i l e d D e s c r i p t i o n
8 Detailed Description
8.1 AS1106 vs. AS1107
The AS1106 and AS1107 are identical except for two features:
8.2 Serial-Addressing Format
Programming the AS1106/AS1107 is done by writing to the device’s internal registers (see Digit- and Control-Registers on page 9) via the 4-wire
serial interface. A programming sequence consists of 16-bit packages as listed in
The data is shifted into the internal 16-bit register with the rising edge of the CLK signal. With the rising edge of the LOAD/CSN signal the data is
latched into a digit- or control-register. The LOAD/CSN signal must go high after the 16th rising clock edge.
The LOAD/CSN signal can also come later but this must happen just before the next rising edge of CLK, otherwise the data will be lost. The
contents of the internal shift register are applied 16.5 clock cycles later to pin DOUT. The data is clocked out at the falling edge of CLK.
The first 4 bits (D15:D12) are “don't care”, bits D11:D8 contain the register address, and bits D7:D0 contain the data. The first bit is D15, the most
significant bit (MSB). The exact timing is shown in
Table 6. 16-Bit Serial Data Format
8.3 Initial Power-Up
On initial power-up, the AS1106/AS1107 registers are reset to their default values, the display is blanked, and the device goes into shutdown
mode. At this time, all registers should be programmed for normal operation.
Note: The default settings enable only scanning of one digit; the internal decoder is disabled and the Intensity Control Register (see page 12)
Figure 12. Interface Timing
www.austriamicrosystems.com/LED-Driver-ICs/AS1106_07
D15
X
LOAD/CSN
The AS1107 segment drivers are slew-rate limited to reduce electromagnetic interference (EMI).
The AS1107 serial interface is fully SPI compatible (programmable for AS1106).
DOUT
is set to the minimum values.
CLK
DIN
D14
X
D13
X
D12
X
t
CSS
t
DS
D15
D11
Register Address (see
t
DH
D10
Figure
t
CL
D14
12.
D9
t
CH
Table
Revision 2.28
D8
7)
MSB
D7
Table
D6
6.
D1
D5
t
CP
t
DO
D4
Data
D0
t
CSH
D3
t
D2
LDCK
t
CSW
D1
LSB
8 - 21
D0