TC7117ACKW713 Microchip Technology, TC7117ACKW713 Datasheet - Page 9
![IC ADC 3 1/2DGT LED DVR 44-MQFP](/photos/6/59/65984/150-44-pqfp_sml.jpg)
TC7117ACKW713
Manufacturer Part Number
TC7117ACKW713
Description
IC ADC 3 1/2DGT LED DVR 44-MQFP
Manufacturer
Microchip Technology
Datasheet
1.TC7116CPL.pdf
(24 pages)
Specifications of TC7117ACKW713
Display Type
LED
Configuration
7 Segment
Digits Or Characters
A/D 3.5 Digits
Current - Supply
800µA
Voltage - Supply
5V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
44-MQFP, 44-PQFP
Lead Free Status / RoHS Status
Request inventory verification / Request inventory verification
Interface
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TC7117ACKW713
Manufacturer:
Microchip Technology
Quantity:
10 000
3.1.5
This input can accept differential voltages anywhere
within the Common mode range of the input amplifier
or, specifically, from 1V below the positive supply to 1V
above the negative supply. In this range, the system
has a CMRR of 86dB, typical. However, since the inte-
grator also swings with the Common mode voltage,
care must be exercised to ensure that the integrator
output does not saturate. A worst-case condition would
be a large, positive Common mode voltage with a near
full scale negative differential input voltage. The nega-
tive input signal drives the integrator positive, when
most of its swing has been used up by the positive
Common mode voltage. For these critical applications,
the integrator swing can be reduced to less than the
recommended 2V full scale swing with little loss of
accuracy. The integrator output can swing within 0.3V
of either supply without loss of linearity.
3.1.6
This pin is included primarily to set the Common mode
voltage for battery operation (TC7116/TC7116A), or for
any system where the input signals are floating, with
respect to the power supply. The analog common pin
sets a voltage approximately 2.8V more negative than
the positive supply. This is selected to give a minimum
end of life battery voltage of about 6V. However, analog
common has some attributes of a reference voltage.
When the total supply voltage is large enough to cause
the Zener to regulate (>7V), the analog common volt-
age will have a low voltage coefficient (0.001%), low
output impedance (≅15Ω), and a temperature coeffi-
cient of less than 20ppm/°C, typically, and 50 ppm max-
imum. The TC7116/TC7117 temperature coefficients
are typically 80ppm/°C.
An external reference may be used, if necessary, as
shown in Figure 3-2.
FIGURE 3-2:
Reference
© 2006 Microchip Technology Inc.
TC7116A
TC7117A
TC7116
TC7117
DIFFERENTIAL INPUT
ANALOG COMMON
COMMON
V+
V
REF
+
Using an External
20kΩ
V+
1.2V REF
6.8kΩ
Analog common is also used as V
auto-zero and de-integrate. If V
log common, a Common mode voltage exists in the
system and is taken care of by the excellent CMRR of
the converter. However, in some applications, V
be set at a fixed, known voltage (power supply common
for instance). In this application, analog common
should be tied to the same point, thus removing the
Common mode voltage from the converter. The same
holds true for the reference voltage; if it can be conve-
niently referenced to analog common, it should be. This
removes the Common mode voltage from the
reference system.
Within the IC, analog common is tied to an N-channel
FET, that can sink 30mA or more of current to hold the
voltage 3V below the positive supply (when a load is
trying to pull the analog common line positive). How-
ever, there is only 10μA of source current, so analog
common may easily be tied to a more negative voltage,
thus overriding the internal reference.
3.1.7
The TEST pin serves two functions. On the TC7117/
TC7117A, it is coupled to the internally generated digi-
tal supply through a 500Ω resistor. Thus, it can be used
as a negative supply for externally generated segment
drivers, such as decimal points, or any other presenta-
tion the user may want to include on the LCD.
(Figure 3-3 and Figure 3-4 show such an application.)
No more than a 1mA load should be applied.
The second function is a “lamp test.” When TEST is
pulled HIGH (to V+), all segments will be turned ON
and the display should read -1888. The TEST pin will
sink about 10mA under these conditions.
FIGURE 3-3:
Decimal Point
TC7116/A/TC7117/A
TC7116A
TC7116
V+
TEST
BP
TEST
21
37
Simple Inverter for Fixed
IN
4049
- is different from ana-
V+
GND
IN
DS21457C-page 9
- return during
To LCD
Decimal
Point
To LCD
Backplane
IN
- will