TC7117CKW713 Microchip Technology, TC7117CKW713 Datasheet - Page 12
![IC ADC 3 1/2DGT LED DVR 44-MQFP](/photos/6/59/65984/150-44-pqfp_sml.jpg)
TC7117CKW713
Manufacturer Part Number
TC7117CKW713
Description
IC ADC 3 1/2DGT LED DVR 44-MQFP
Manufacturer
Microchip Technology
Datasheet
1.TC7116CPL.pdf
(24 pages)
Specifications of TC7117CKW713
Display Type
LED
Configuration
7 Segment
Digits Or Characters
A/D 3.5 Digits
Current - Supply
800µA
Voltage - Supply
5V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
44-MQFP, 44-PQFP
Lead Free Status / RoHS Status
Request inventory verification / Request inventory verification
Interface
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
TC7117CKW713
Manufacturer:
Microchip Technology
Quantity:
10 000
TC7116/A/TC7117/A
4.0
4.1
The size of the auto-zero capacitor has some influence
on system noise. For 200mV full scale, where noise is
very important, a 0.47μF capacitor is recommended.
On the 2V scale, a 0.047μF capacitor increases the
speed of recovery from overload and is adequate for
noise on this scale.
4.2
A 0.1μF capacitor is acceptable in most applications.
However, where a large Common mode voltage exists
(i.e., the V
200mV scale is used, a larger value is required to pre-
vent rollover error. Generally, 1μF will hold the rollover
error to 0.5 count in this instance.
4.3
The integrating capacitor should be selected to give the
maximum voltage swing that ensures tolerance buildup
will not saturate the integrator swing (approximately
0.3V from either supply). In the TC7116/TC7116A or
the TC7117/TC7117A, when the analog common is
used as a reference, a nominal ±2V full scale integrator
swing is acceptable. For the TC7117/TC7117A, with
±5V supplies and analog common tied to supply
ground, a ±3.5V to ±4V swing is nominal. For 3 read-
ings per second (48kHz clock), nominal values for C
are 0.22μ1F and 0.10μF, respectively. If different oscil-
lator frequencies are used, these values should be
changed in inverse proportion to maintain the output
swing. The integrating capacitor must have low dielec-
tric absorption to prevent rollover errors. Polypropylene
capacitors are recommended for this application.
4.4
Both the buffer amplifier and the integrator have a class
A output stage with 100μA of quiescent current. They
can supply 20μA of drive current with negligible non-
linearity. The integrating resistor should be large
enough to remain in this very linear region over the
input voltage range, but small enough that undue leak-
age requirements are not placed on the PC board. For
2V full scale, 470kΩ is near optimum and, similarly,
47kΩ for 200mV full scale.
DS21457C-page 12
COMPONENT VALUE
SELECTION
Auto-Zero Capacitor
Reference Capacitor
Integrating Capacitor
Integrating Resistor
IN
- pin is not at analog common), and a
INT
4.5
For all frequency ranges, a 100kΩ resistor is recom-
mended; the capacitor is selected from the equation:
EQUATION 4-1:
For a 48kHz clock (3 readings per second), C = 100pF.
4.6
To generate full scale output (2000 counts), the analog
input requirement is V
and 2V scale, V
respectively. In many applications, where the ADC is
connected to a transducer, a scale factor exists
between the input voltage and the digital reading. For
instance, in a measuring system, the designer might like
to have a full scale reading when the voltage from the
transducer is 700mV. Instead of dividing the input down
to 200mV, the designer should use the input voltage
directly and select V
integrating resistor and capacitor would be 120kW and
0.22μF. This makes the system slightly quieter and also
avoids a divider network on the input. The TC7117/
TC7117A, with ±5V supplies, can accept input signals
up to ±4V. Another advantage of this system is when a
digital reading of zero is desired for V
ture and weighing systems with a variable tare are
examples. This offset reading can be conveniently gen-
erated by connecting the voltage transducer between
V
offset voltage between analog common and V
IN
+ and analog common, and the variable (or fixed)
Oscillator Components
Reference Voltage
REF
f
REF
IN
=
should equal 100mV and 1V,
© 2006 Microchip Technology Inc.
= 2V
= 350mV. Suitable values for
0.45
- - - - - - -
RC
REF
. Thus, for the 200mV
IN
≠ 0. Tempera-
IN
-.