LTC1645CS#PBF Linear Technology, LTC1645CS#PBF Datasheet - Page 13
![IC CTLR HOT SWAP SEQ DUAL 14SOIC](/photos/7/36/73601/ltc1645cs_pbf_sml.jpg)
LTC1645CS#PBF
Manufacturer Part Number
LTC1645CS#PBF
Description
IC CTLR HOT SWAP SEQ DUAL 14SOIC
Manufacturer
Linear Technology
Type
Hot-Swap Controllerr
Datasheet
1.LTC1645CS8PBF.pdf
(24 pages)
Specifications of LTC1645CS#PBF
Applications
General Purpose
Internal Switch(s)
No
Voltage - Supply
1.2 V ~ 12 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
14-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
V
voltage on the external capacitor C
with a slope dv/dt = 2 A/C
the trip point (1.23V), the timer is reset by pulling the
TIMER pin back to ground. The timer period is
t = (1.23V • C
capacitor.
Electronic Circuit Breaker
The LTC1645 features an electronic circuit breaker func-
tion that protects against short circuits or excessive out-
put currents. By placing sense resistors between the
supply inputs and sense pins of the supplies, the circuit
breaker trips whenever the voltage across either sense
resistor is greater than 50mV for more than 1.5 s. If the
circuit breaker trips, both GATE pins are immediately
pulled to ground and the external N-channels FETs are
quickly turned off (time point 6 in Figure 12). The circuit
breaker resets and another timing cycle starts by taking
CC n
– V
Figure 13. Extending the Short-Circuit Protection Delay
SENSE n
TIMER
GATE n
RESET
V
V
OUT n
CC n
ON
1 2
TIMER
Figure 12. Current Fault Timing
RAMPING UP
)/2 A. For a 200ms delay, use a 0.33 F
3
U
V
4
CC n
C
F
SENSE n
TIMER
LTC1645
U
CURRENT
5
FAULT
R
F
6
. When the voltage reaches
GATE n
7
TIMER
W
AND RAMP UP
RESET FAULT
8
1645 G13
starts to ramp up
9
1645 F12
10
U
ON
the ON pin below 0.4V and then high as shown at time
point 7.
At the end of the timer cycle (time point 8), the charge
pump turns on again. If the circuit breaker feature is not
required, short the SENSE n pin to V
If the 1.5 s response time is too fast to reject supply noise,
add external resistors and capacitors R
sense circuit as shown in Figure 13.
The ON Pin
The ON pin is used to control system operation as shown
in Figure 14. At time point 1, the board makes connection
and the supplies power up the chip. At time point 2, the ON
pin goes high and a timer cycle starts as long as both V
pins are higher than the undervoltage lockout trip point
(2.23V for V
fault is not detected. At the end of the timer cycle (time
point 3), the charge pump is turned on and the GATE n pin
voltages start to ramp up with the output supply voltages,
V
At time point 4, V
(this example assumes the FB pin resistive divider is
connected to V
of the timing cycle (time point 5), RESET goes high and the
power-up process is complete.
TIMER
RESET
GATE1
GATE2
V
V
V
OUT n
OUT1
OUT2
CC n
0.8V
0.4V
0V
2V
, following one gate-to-source voltage drop lower.
1 2
RAMPING UP AND
DOWN TOGETHER
3
CC1
4
OUT2
5
Figure 14. ON Pin Waveforms
and 1.12V for V
OUT2
6 7
) and a timing cycle starts. At the end
reaches its power-good trip level
8
9
DOWN SEPARATELY
RAMPING UP AND
10 11 12 13 14 15 16 17 18 19 20
CC2
) and an overcurrent
CC n
.
F
LTC1645
and C
TURNING OFF FAST
RAMPING UP AND
F
13
to the
1645fa
1645 F14
CC