LTC4252A-1CMS#TRPBF Linear Technology, LTC4252A-1CMS#TRPBF Datasheet - Page 10
![IC CNTRLR HOTSWAP NEGVOLT 10MSOP](/photos/1/36/13608/10-msop_05-08-1661_sml.jpg)
LTC4252A-1CMS#TRPBF
Manufacturer Part Number
LTC4252A-1CMS#TRPBF
Description
IC CNTRLR HOTSWAP NEGVOLT 10MSOP
Manufacturer
Linear Technology
Type
Hot-Swap Controllerr
Specifications of LTC4252A-1CMS#TRPBF
Applications
General Purpose
Internal Switch(s)
No
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
10-TFSOP, 10-MSOP (0.118", 3.00mm Width)
Family Name
LTC4252A-1
Package Type
MSOP
Operating Temperature (min)
0C
Operating Temperature (max)
70C
Operating Temperature Classification
Commercial
Product Depth (mm)
3mm
Product Height (mm)
0.86mm
Product Length (mm)
3mm
Mounting
Surface Mount
Pin Count
10
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
PI FU CTIO S
LTC4252-1/LTC4252-2
LTC4252A-1/LTC4252A-2
V
this pin to the negative side of the power supply.
GATE (Pin 6/Pin 5): N-Channel MOSFET Gate Drive Out-
put. This pin is pulled high by a 58µA current source. GATE
is pulled low by invalid conditions at V
or a circuit breaker fault timeout. GATE is actively servoed
to control the fault current as measured at SENSE. A
compensation capacitor at GATE stabilizes this loop. A
comparator monitors GATE to ensure that it is low before
allowing an initial timing cycle, GATE ramp-up after an
overvoltage event or restart after a current limit fault.
During GATE start-up, a second comparator detects if
GATE is within 2.8V of V
package only).
DRAIN (Pin 7/Pin 6): Drain Sense Input. Connecting an
external resistor, R
drain (V
LTC4252A) and current feedback to TIMER. A comparator
detects if DRAIN is below 2.385V and together with the
GATE high comparator sets the PWRGD flag. If V
above V
The current through R
added to TIMER’s 230µA pullup current during a circuit
breaker fault cycle. This reduces the fault time and MOSFET
heating.
OV (Pin 8/Pin7): Overvoltage Input. The active high thresh-
old at the OV pin is set at 6.15V with 0.6V hysteresis. If OV
> 6.15V, GATE pulls low. When OV returns below 5.55V,
GATE start-up begins without an initial timing cycle. The
LTC4252A OV pin is set at 5.09V with 102mV hysteresis.
If OV > 5.09V, GATE pulls low. When OV returns below
4.988V, GATE start-up begins without an initial timing
cycle. If an overvoltage condition occurs in the middle of
an initial timing cycle, the initial timing cycle is restarted
after the overvoltage condition goes away. An overvoltage
condition does not reset the PWRGD flag. The internal
UVLO at V
at OV prevents transients and switching noise from affect-
ing the OV thresholds and prevents glitches at the GATE
pin.
10
EE
U
(Pin 5/Pin 4): Negative Supply Voltage Input. Connect
OUT
DRNCL
IN
U
) allows voltage sensing below 6.15V (5V for
always overrides OV. A 1nF to 10nF capacitor
, DRAIN clamps at approximately V
D
, between this pin and the MOSFET’s
U
D
is internally multiplied by 8 and
IN
(MS/MS8)
before PWRGD is set (MS
IN
(UVLO), UV, OV,
DRNCL
OUT
is
.
UV (Pin 9/Pin 7): Undervoltage Input. The active low
threshold at the UV pin is set at 2.925V with 0.3V hyster-
esis. If UV < 2.925V, PWRGD pulls high, both GATE and
TIMER pull low. If UV rises above 3.225V, this initiates an
initial timing cycle followed by GATE start-up. The
LTC4252A UV pin is set at 3.08V with 324mV hysteresis.
If UV < 2.756V, PWRGD pulls high, both GATE and TIMER
pull low. If UV rises above 3.08V, this initiates an initial
timing cycle followed by GATE start-up. The internal UVLO
at V
fault latch. A 1nF to 10nF capacitor at UV prevents tran-
sients and switching noise from affecting the UV thresh-
olds and prevents glitches at the GATE pin.
TIMER (Pin 10/Pin 8): Timer Input. TIMER is used to
generate an initial timing delay at start-up and to delay
shutdown in the event of an output overload (circuit
breaker fault). TIMER starts an initial timing cycle when
the following conditions are met: UV is high, OV is low, V
clears UVLO, TIMER pin is low, GATE is lower than V
SS < 0.2V, and V
5.8µA then charges C
charges to V
quickly pulls low and GATE is activated.
If SENSE exceeds 50mV while GATE is high, a circuit
breaker cycle begins with a 230µA pull-up current charg-
ing C
during this cycle, the timer pull-up has an additional
current of 8 • I
TIMER reaches 4V, a 5.8µA pull-down current slowly
discharges the C
grates up to the V
GATE quickly pulls low and PWRGD pulls high. The
LTC4252-1 TIMER pin latches high with a 5.8µA pull-up
source. This latched fault is cleared by either pulling
TIMER low with an external device or by pulling UV below
V
following an overcurrent fault. This cycle consists of 4
discharging ramps and 3 charging ramps. The charging
and discharging currents are 5.8µA and TIMER ramps
between its 1V and 4V thresholds. At the completion of a
shutdown cooling cycle, the LTC4252-2 attempts a start-
up cycle.
UVLO
IN
T
always overrides UV. A low at UV resets an internal
. If DRAIN is approximately 7V (6V for LTC4252A)
. The LTC4252-2 starts a shutdown cooling cycle
TMRH
DRN
TMRH
SENSE
T
(4V), the timing cycle terminates, TIMER
. In the event that C
. If SENSE drops below 50mV before
threshold, the circuit breaker trips,
T
– V
, generating a time delay. If C
EE
< V
CB
. A pull-up current of
T
eventually inte-
GATEL
425212fb
IN
T
,