MIC2583-MYQS TR Micrel Inc, MIC2583-MYQS TR Datasheet - Page 19
![IC CTRLR HOT SWAP 200MV 16-QSOP](/photos/14/17/141715/16-qsop_sml.jpg)
MIC2583-MYQS TR
Manufacturer Part Number
MIC2583-MYQS TR
Description
IC CTRLR HOT SWAP 200MV 16-QSOP
Manufacturer
Micrel Inc
Type
Hot-Swap Controllerr
Datasheet
1.MIC2582-JYM.pdf
(25 pages)
Specifications of MIC2583-MYQS TR
Applications
General Purpose
Internal Switch(s)
No
Voltage - Supply
2.3 V ~ 13.2 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
16-SSOP (0.150", 3.90mm Width)
Linear Misc Type
Positive Low Voltage
Family Name
MIC2583
Package Type
QSOP
Operating Supply Voltage (min)
2.3V
Operating Supply Voltage (max)
13.2V
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Product Depth (mm)
3.99mm
Product Height (mm)
1.4mm
Product Length (mm)
4.98mm
Mounting
Surface Mount
Pin Count
16
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
MIC2583-MYQSTR
MIC2583-MYQSTR
MIC2583-MYQSTR
MOSFET Selection
Selecting the proper external MOSFET for use with the
MIC2582/83 involves three straightforward tasks:
• Choice of a MOSFET which meets minimum voltage
• Selection of a device to handle the maximum
• Verify the selected part’s ability to withstand any peak
MOSFET Voltage Requirements
The first voltage requirement for the MOSFET is easily
stated: the drain-source breakdown voltage of the
MOSFET must be greater than V
12V input may reasonably be expected to see high-
frequency transients as high as 18V. Therefore, the
drain-source breakdown voltage of the MOSFET must
be at least 19V. For ample safety margin and standard
availability, the closest value will be 20V.
The second breakdown voltage criterion that must be
met is a bit subtler than simple drain-source breakdown
voltage, but is not hard to meet. In MIC2582/83
applications, the gate of the external MOSFET is driven
up to approximately 19.5V by the internal output
Micrel, Inc.
April 2009
requirements.
continuous current (steady-state thermal issues).
currents (transient thermal issues).
IN(MAX)
. For instance, a
Figure 9. Zener Clamped MOSFET Gate
19
MOSFET (again, assuming 12V operation).
At the same time, if the output of the external MOSFET
(its source) is suddenly subjected to a short, the gate-
source voltage will go to (19.5V – 0V) = 19.5V. This
means that the external MOSFET must be chosen to
have a gate-source breakdown voltage of 20V or more,
which is an available standard maximum value.
However, if operation is at or above 13V, the 20V gate-
source maximum will likely be exceeded. As a result, an
external Zener diode clamp should be used to prevent
breakdown of the external MOSFET when operating at
voltages above 8V. A Zener diode with 10V rating is
recommended as shown in Figure 9. At the present time,
most power MOSFETs with a 20V gate-source voltage
rating have a 30V drain-source breakdown rating or
higher.
As a general tip, choose surface-mount devices with a
drain-source rating of 30V as a starting point.
Finally, the external gate drive of the MIC2582/83
requires a low-voltage logic level MOSFET when
operating at voltages lower than 3V. There are 2.5V
logic level MOSFETs available. Please see Table 4
“
suggested manufacturers.
MOSFET and Sense Resistor Vendors”
MIC2582/MIC2583
M9999-043009-C
for