MIC2586R-1BM TR Micrel Inc, MIC2586R-1BM TR Datasheet - Page 10
![IC CTRLR/SEQ HOT SWAP 14-SOIC](/photos/6/84/68433/576-14-soic_sml.jpg)
MIC2586R-1BM TR
Manufacturer Part Number
MIC2586R-1BM TR
Description
IC CTRLR/SEQ HOT SWAP 14-SOIC
Manufacturer
Micrel Inc
Type
Hot-Swap Controllerr
Datasheet
1.MIC2586R-1YM.pdf
(17 pages)
Specifications of MIC2586R-1BM TR
Applications
General Purpose
Internal Switch(s)
No
Voltage - Supply
10 V ~ 80 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
14-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
MIC2586R-1BMTR
MIC2586R-1BMTR
MIC2586R-1BMTR
Functional Description
Hot Swap Insertion
When circuit boards are inserted into systems carrying live
supply voltages ("hot swapped"), high inrush currents often
result due to the charging of bulk capacitance that resides
across the circuit board's supply pins. These current spikes
can cause the system's supply voltages to temporarily go out
of regulation causing data loss or system lock-up. In more
extreme cases, the transients occurring during a hot swap
event may cause permanent damage to connectors or on-
board components.
The MIC2586/MIC2586R is designed to address these
issues by limiting the maximum current that is allowed to flow
during hot swap events. This is achieved by implementing a
constant-current control loop at turn-on. In addition to inrush
current control, the MIC2586 and MIC2586R incorporate
input voltage supervisory functions and user-programmable
overcurrent protection, thereby providing robust protection for
both the system and the circuit board.
Input Supply Transient Suppression and Filtering
The
transient voltage spikes up to 100V.
spikes in excess of 100V may cause damage to the
controller.
parasitic inductances, wide (and short) power traces should
be utilized. Alternatively, a heavier trace plating will help
minimize inductive spikes that may arise during events (e.g.,
short circuit loads) that can cause a large di/dt to occur.
External surge protection, such as a clamping diode, is also
recommended as an added safeguard for device (and
system) protection. Lastly, a 0.1µF filter capacitor is
recommended to help reject additional noise.
Start-Up Cycle
When the power supply voltage to the MIC2586/MIC2586R is
higher than the V
cycle is initiated. When the controller is enabled, an internal
16µA current source (I
voltage rises from 0V with respect to ground at a rate equal
to:
The internal charge pump has sufficient output drive to fully
enhance commonly available power MOSFETs for the lowest
possible DC losses.
between 7.5V and 18V over the entire supply voltage
operating range (10V to 80V), so 60V BV
N-channel power MOSFETs can be used for +48V and +24V
applications, respectively. However, an external Zener diode
(18-V) connected from the source to the gate as shown in the
"Typical Applications" circuit is highly recommended. A good
Micrel
October 2004
dV
MIC2586/MIC2586R
dt
GATE
=
I
In order to suppress transients caused by
GATEON
C
GATE
UVH
and the V
GATEON
The gate drive is guaranteed to be
is
) is enabled and the GATE pin
ONH
guaranteed
threshold voltages, a start
DSS
However, voltage
and 30V BV
to
withstand
(1)
DSS
10
choice for an 18-V Zener diode in this application is the
MMSZ5248B, available in a small SOD123 package.
C
minimizes
oscillations from occurring in M1. However, note that
resistance in this part of the circuit has a slight destabilizing
effect upon the MIC2586/MIC2586R's current regulation
loop. Compensation resistor R4 is necessary for stabilization
of the current regulation loop. The current through the power
transistor during initial inrush is given by:
The drain current of the MOSFET is monitored via an
external current sense resistor to ensure that it never
exceeds the programmed threshold, as described in the
"Circuit Breaker Operation" section.
A capacitor connected to the controller’s TIMER pin sets the
value of overcurrent detector delay, t
which an overcurrent event must last to signal a fault
condition and to cause an output latch-off. These devices will
be driving a capacitive load in most applications, so a
properly chosen value of C
tripping at turn-on as well as providing immunity to noise
spikes after the start-up cycle is complete. The procedure for
selecting a value for C
Operation" section.
Overcurrent Protection
The MIC2586 and the MIC2586R use an external, low-value
resistor in series with the drain of the external MOSFET to
measure the current flowing into the load. The VCC
connection (Pin 14) and the SENSE connection (Pin 13) are
the (+) and (-) inputs, respectively, of the device's internal
current sensing circuits.
strongly recommended for sensing the voltage across these
pins. See the “Applications Information” for further details.
The nominal current limit is determined by the following
equation.
where V
in the datasheet and R
sense resistor. As the MIC2586 and the MIC2586R employ
a constant-current regulation scheme in current limit, the
charge pump’s output voltage at the GATE pin is adjusted so
that the voltage across the external sense resistor is held
equal to V
pin is being charged. If the current-limit condition goes away
before the TIMER pin voltage rises above the V
threshold, then steady-state operation resumes. To prevent
excessive power dissipation in the external MOSFET under
load current fault conditions, the FB pin voltage is used as
GATE
is used to adjust the GATE voltage slew rate while R3
I
INRUSH
TRIP(TYP)
TRIP
I
LIMIT
the
= C
while the capacitor connected to the TIMER
LOAD
is the typical current limit threshold specified
=
V
potential
R
TRIP(TYP)
×
SENSE
I
GATEON
C
TIMER
GATE
SENSE
TIMER
Kelvin sense connections are
is given in the "Circuit Breaker
for
is the value of the selected
prevents false-, or nuisance-,
high-frequency
FLT
MIC2586/MIC2586R
, which is the time for
(408) 955-1690
M9999-102204
parasitic
(3)
(2)
TIMERH