MIC2587R-1BM TR Micrel Inc, MIC2587R-1BM TR Datasheet
MIC2587R-1BM TR
Specifications of MIC2587R-1BM TR
MIC2587R-1BMTR
Related parts for MIC2587R-1BM TR
MIC2587R-1BM TR Summary of contents
Page 1
... General Description The MIC2587 and MIC2587R are single-channel positive voltage hot swap controllers designed to provide safe insertion and removal of boards for systems that require live (always-powered) backplanes. These devices use few external components and act as controllers for external N- channel power MOSFET devices to provide inrush current control and output voltage slew rate control ...
Page 2
... Micrel Typical Application Pin Configuration 8-pin SOIC (M) MIC2587-1BM MIC2587R-1BM October 2004 MIC2587/87R Typical Application Circuit 2 MIC2587/MIC2587R 8-pin SOIC (M) MIC2587-2BM MIC2587R-2BM M9999-102204 (408) 955-1690 ...
Page 3
... When the voltage at the TIMER pin is less than 0.5V, the TIMERDN MIC2587 can be restarted by toggling the ON pin LOW then HIGH. For the MIC2587R, the capacitor connected to the TIMER pin sets the period of auto-retry where the duty cycle is fixed at a nominal 5%. 3 ...
Page 4
... VCC pin can be tied together. Positive Supply Voltage Input: This pin is the (+) Kelvin sense connection for the output supply rail. The nominal operating voltage range for the MIC2587 and the MIC2587R is +10V to +80V, and VCC can withstand input transients up to +100V. An undervoltage ...
Page 5
... CC SENSE TRIP = V ) GATE[TH GATE Normal turn-off, or from V (MOSFET after a fault condition (V – > SENSE TRIP TIMER 5 MIC2587/MIC2587R (2) )...................................... +10V to +80V CC ) ............... -40°C to +85° ....................................... +125° 8-pin SOIC...................................................... 160 °C/W Min Typ 10 2 7.5 8.0 7.0 7.5 500 1.280 1.313 1.208 1 ...
Page 6
... PG C =100pF 50kΩ pull-up to 48V PG C =100pF 50kΩ pull-up to 48V PG C =100pF 10mV) CC SENSE TRIP Figure 7 6 MIC2587/MIC2587R Min Typ 1.5 3.5 1.280 1.313 0.4 0.49 1.280 1.313 1.208 1.233 80 Min Typ 3 = 10nF Max Units µ ...
Page 7
... Micrel Timing Diagrams Figure 1. Foldback Current Limit Transfer Characteristic Figure 3. MIC2587/87R PWRGD Timing October 2004 Figure 4. MIC2587/87R /PWRGD Timing Figure 5. Overcurrent Sense to GATE Timing 7 MIC2587/MIC2587R Figure GATE Timing M9999-102204 (408) 955-1690 ...
Page 8
... Micrel Function Diagram October 2004 MIC2587/MIC2587R Block Diagram 8 MIC2587/MIC2587R M9999-102204 (408) 955-1690 ...
Page 9
... The procedure for selecting a value for C given in the "Circuit Breaker Operation" section. Overcurrent Protection The MIC2587 and the MIC2587R use an external, low- value resistor in series with the drain of the external MOSFET to measure the current flowing into the load. The VCC connection (Pin 8) and the SENSE connection (Pin 7) are the (+) and (-) inputs, respectively, of the device's internal current sensing circuits ...
Page 10
... SENSE the circuit’s V pin and SENSE CC MIC2587/MIC2587R, a fault current timing circuit is set via an external capacitor (C ) that determines the length of TIMER the time delay (t ) for which the controller remains in FLT current limit before the circuit breaker is tripped. Programming the response time of the overcurrent detector ...
Page 11
... UVL October 2004 Power-is-Good Output Signals until For the MIC2587-1 and MIC2587R-1, the power-good TIMERDN output signal (PWRGD) will be high impedance when the TIMERL FB pin voltage is higher than the V pull down to GND when the FB pin voltage is lower than ...
Page 12
... Micrel Applications Information External ON/OFF Control The MIC2587/MIC2587R have an ON pin input that is used to enable the controller to commence a start-up sequence upon card insertion or to disable controller operation upon card removal. In addition, the ON pin can be used to reset the MIC2587/MIC2587R’s internal electronic circuit breaker in the event of a load current fault ...
Page 13
... P = (5.8A) MAX A 0.5W sense resistor is a good choice in this application. When the MIC2587/MIC2587R’s foldback current limiting circuit is engaged in the above example, the current limit would nominally fold back to 1.23A when the output is shorted to ground. PCB Layout Recommendations 4-Wire Kelvin Sensing ...
Page 14
... Micrel Figure 6. 4-Wire Kelvin Sense Connections for R Figure 8. Recommended PCB Layout for Sense Resistor, October 2004 Figure 7. Current Limit Sense Filter for Noisy SENSE Power MOSFET, Timer and Feedback Network. 14 MIC2587/MIC2587R Systems M9999-102204 (408) 955-1690 ...
Page 15
... Series www.vishay.com/docswsl_30100.pdf (203) 452-5664 “OARS” Series www.irctt.com/pdf_files/OARS.pdf “LR” Series www.irctt.com/pdf_files/LRC.pdf second source to “WSL” (828) 264-8861 Table 1. MOSFET and Sense Resistor Vendors 15 MIC2587/MIC2587R ) Contact Information DSS 60V www.siliconix.com 60V (203) 452-5664 60V 100V www.siliconix.com ...
Page 16
... Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any October 2004 8-Pin SOIC (M) damages resulting from such use or sale. © 2004 Micrel, Incorporated. 16 MIC2587/MIC2587R M9999-102204 (408) 955-1690 ...