MIC2588-2BM Micrel Inc, MIC2588-2BM Datasheet
![IC CTRLR HOT SWAP NEG HV 8-SOIC](/photos/6/50/65078/576-8-soic_sml.jpg)
MIC2588-2BM
Specifications of MIC2588-2BM
Related parts for MIC2588-2BM
MIC2588-2BM Summary of contents
Page 1
... Fault reporting: Active-HIGH (-1BM) and Active-LOW (-2BM) Power-Good output signal Applications • Central office switching • –48V power distribution • Distributed power systems • Server Networks 1 8 /PWRGD VDD DRAIN R2 MIC2588-2BM 11.8kΩ GATE 4 5 VEE SENSE *C2 22nF R4 VDD 10Ω C3 ...
Page 2
... Latched Off 8-pin SOIC Latched Off 8-pin SOIC Latched Off 8-pin SOIC Latched Off 8-pin SOIC 1 8 VDD DRAIN GATE VEE 4 5 SENSE 8-Pin SOIC (M) MIC2588-2BM 1 8 VDD DRAIN OFF 3 6 GATE VEE 4 5 SENSE 8-Pin SOIC (M) MIC2594-2BM September 2005 Micrel ...
Page 3
... OFF pin, the voltage on the ON pin must exceed the V threshold in order for the MIC2594 to be enabled. ONH MIC2588: Undervoltage Threshold Input. When the voltage at the UV pin is less than the V threshold, the GATE pin is immediately pulled low by an UVL internal 100µ ...
Page 4
... MIC2588/MIC2594 Absolute Maximum Ratings (All voltages are referred Supply Voltage (V – ...........................–0.3V to 100V DD EE DRAIN, PWRGD pins ....................................–0.3V to 100V GATE pin ......................................................–0.3V to 12.5V SENSE, OV, UV, ON, OFF pins .........................–0. Lead Temperature (soldering) Standard package (-xBM) (IR Reflow, Peak Temperature) ........ 240°C +0°C/–5°C Pb-Free Package-(xYM) (IR Refl ...
Page 5
... MIC2588/MIC2594 AC Electrical Characteristics Symbol Parameter t Built-in Overcurrent Nuisance Trip FLT (6) Time Delay (Figure 1) t Overcurrent Sense to GATE Low OCSENSE (Figure 2) ( GATE Low (Figure 3) OVPHL ( GATE High (Figure 3) OVPLH ( GATE Low (Figure 4) UVPHL ( GATE High (Figure 4) UVPLH t DRAIN High to PWRGD Output Low ...
Page 6
... MIC2588/MIC2594 GATE GATE MIC2588/94-1 V DRAIN PWRGD not asserted V PWRGD PWRGD MIC2588/94-2 V DRAIN /PWRGD September 2005 1.223V t OVPHL 1V Figure 3. Overvoltage Response 1.223V t UVPHL 1V Figure 4. Undervoltage Response V V PGTH PGTH PGH1 PGL1 PWRGD asserted - High Impedance Ð DRAIN PGTH PGL2 V EE Figure 5. DRAIN to Power-Good Response 6 1 ...
Page 7
... MIC2588/MIC2594 Typical Characteristics [Section under construction] Supply Current vs. Temperature -40 - 100 TEMPERATURE (°C) GATE Drive ( GATE EE vs. Supply Voltage 25° SUPPLY VOLTAGE (V) UV Pin Threshold vs. Temperature 1.28 1.27 1.26 1.25 V UVH 1.24 1.23 V UVL 1.22 1.21 1.2 -40 - 100 TEMPERATURE (°C) Power-Good Low Voltage vs ...
Page 8
... RTN (Long Pin) 47kΩ R1 698kΩ 1% *D1 SMAT70A R3 12.4kΩ 1uF -48V IN (Long Pin) M9999-083005 /PWRGD VDD DRAIN R2 MIC2588-2BM 11.8kΩ GATE 4 5 VEE SENSE C2 0.22uF R SENSE (see photos) MIC2588/MIC2594 Test Circuit 8 -48V RTN C5 C4 100uF 0.1uF R C FDBK FDBK 10kΩ ...
Page 9
... MIC2588/MIC2594 Functional Characteristics Turn-On Response TIME (5ms/div.) Turn-On (Circuit Breaker Trip) Into Large C Circuit Breaker Trips TIME (100µs/div.) M9999-083005 R = 0.05Ω SENSE C = 22nF FDBK LOAD R = 0.01Ω SENSE C = 1500µ 6.8nF FDBK C = 0.22µ Hot-Plug Turn-On Response R = 0.05Ω SENSE ...
Page 10
... SENSE + – VEE 50mV UV – TH(UV/OV) – September 2005 V DD1 and V REF1 Current Limit State Nuisance Trip Filter (400s) Logic + Circuit Breaker MIC2588 Block Diagram 10 V DD1 45A GATE 100 DD1 PWRGD V EE /PWRGD – DRAIN Clamp + V Internal PGTH ...
Page 11
... For example, we can determine appropriate capacitor values given a hot swap controller that is required to maintain the inrush current into a 220µF load capacitance at 2A maximum and an input supply voltage as high the suggested MOSFETs to be used with the MIC2588/ MIC2594 is an SUM110N10-09,a 100V D has a typical C Calculating a value for C ...
Page 12
... MOSFET quickly and disconnects the input from the load. Undervoltage/Overvoltage Detection—MIC2588 The MIC2588 has “UV” and “OV” input pins. These pins can be used to detect input supply rail undervoltage and overvoltage conditions. Undervoltage lockout prevents energizing the load until the supply input is stable and within tolerance ...
Page 13
... MIC2588/MIC2594 the OFF pin falls below its V threshold value, or the part OFFL turns off due to a fault. Should either event occur, the GATE pin is immediately pulled low and will remain low until the ON pin once again exceeds its V ONH turn-on and turn-off points are set using the resistor divider R1, R2, and R3 as shown in the “ ...
Page 14
... Managing these repeated voltage stresses with sufficient input bulk capacitance and/or tran- sient suppressing diode clamps is highly recommended for maximizing the life of the hot swap controller(s). *R5 47kΩ /PWRGD VDD 698kΩ DRAIN R2 MIC2588-2BM 11.8kΩ GATE * 68V VEE SENSE *M2 C2 0.22uF *C6 0.47uF *R6 2.7kΩ ...
Page 15
... O resistor 3% low in value: I HOT_SWAP(max) In this case, the application circuit must be sturdy enough to operate up to approximately 1.5x the steady-state hot swap load current. For example MIC2588 circuit must pass a minimum hot swap load current of 4A without nuisance trips, R SENSE R SENSE(nom) where the nearest 1% standard value is 10.0mΩ. At the ...
Page 16
... V IN(MAX) DD The second breakdown voltage criterion that must be met is the gate-source voltage. For the MIC2588/MIC2594, the gate of the external MOSFET is driven maximum of 11V above VEE. This means that the external MOSFET must be chosen to have a gate-source breakdown voltage of 12V or more; 20V is recommended. Most power MOSFETs with a 20V gate-source voltage rating have a 30V drain-source breakdown rating or higher ...
Page 17
... The use of the Transient Thermal Impedence Curves is (10) necessary to determine the increase in junction temperature associated with a worst-case transient condition. From our previous calculation of the maximum power dissipated during a short circuit event for the MIC2588/MIC2594, we calculate the transient junction temperature increase as: T (transient – R ...
Page 18
... PCBs. is SENSE PCB Track Width: 0.03" per Ampere using 1oz Cu Figure 8. 4-Wire Kelvin Sense Connections for R and Return) EE GROUND PAD MIC2588-2BM Via to the /PWRGD VDD power (VEE output) plane OV DRAIN R2 UV GATE VEE ...
Page 19
... MIC2588/MIC2594 MOSFET and Sense Resistor Vendors Device types, part numbers, and manufacturer contacts for power MOSFTETS and sense resistors are provided in Table 1. MOSFET Vendors Key MOSFET Type(s) SUM75N06-09L (TO-263) SUM70N06-11 (TO-263) SUM50N06-16L (TO-263) Vishay - Siliconix SUP85N10-10 (TO-220AB) SUB85N10-10 (TO-263) SUM110N10-09 (TO-263) ...
Page 20
... The circuit of Figure 10 shows how to con- figure an optoisolator driven by the /PWRGD signal of the MIC2588 controller MOC207 /PWRGD VDD DRAIN R2 MIC2588-2BM 11.8 kΩ GATE 4 5 VEE SENSE *C2 22nF R4 VDD *C6 10Ω 0.33uF C3 0 ...
Page 21
... MIC2588/MIC2594 Package Information 0.026 (0.65) MAX) 0.157 (3.99) 0.150 (3.81) 0.064 (1.63) 0.045 (1.14) MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 TEL The information furnished by Micrel in this datasheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. ...