MIC2593-2BTQ TR Micrel Inc, MIC2593-2BTQ TR Datasheet - Page 5

• Manufacturer Part Number: MIC2593-2BTQ TR
• Description: IC PCI HOT PLUG CTLR DUAL 48TQFP
• Manufacturer: Micrel Inc
• Type: Hot-Swap Controllerr

Specifications of MIC2593-2BTQ TR

• Applications: PCI, PCI-X
• Internal Switch(s): No
• Voltage - Supply: 3.3V, 5V, ±12V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 48-TQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: MIC2593-2BTQTR; MIC2593-2BTQTR

Micrel, Inc.
September 2008
Pin Number
15, 22
44, 43
45, 42
40, 41
33, 46
2, 35
1, 36
4, 38
48
47
37
CFILTERA, CFILTERB
AUXENA, AUXENB
/FAULTA, /FAULTB
VAUXA, VAUXB
GPIA, GPIB
ONA, ONB
Pin Name
A1, A0
GND
SDA
SCL
/INT
Pin Function
3.3VAUX[A/B] Output to PCI Card Slot: These outputs connect the 3.3AUX pin
of the PCI connectors to VSTBY[A/B] via internal 400mΩ MOSFETs. These
outputs are current limited and protected against short-circuit faults.
Enable Inputs: Rising-edge triggered. Used to enable or disable the MAINA and
MAINB (5V, 3.3V, +12V and –12V) outputs. Taking ON[A/B] low after a fault
resets the 5V, 3.3V, +12V and/or –12V fault latches for the affected slot. Tie
these pins to GND if using SMI power control. Also, see pin description for
/FAULTA and /FAULTB.
Enable Inputs: Rising-edge triggered. Used to enable or disable VAUXA and
VAUXB outputs. Taking AUXEN[A/B] low after a fault resets the respective slot’s
Aux Output Fault Latch. Tie these pins to GND if using SMI power control. Also,
see pin description for /FAULTA and /FAULTB.
Overcurrent Timer (Filter) Capacitor [A/B]: Capacitors connected between these
pins and GND set the duration of t
remains in current limit before its circuit breaker is tripped.
/FAULT[A/B] Outputs: Open-drain, active-low. Asserted whenever the circuit
breaker trips due to a fault condition (overcurrent, input undervoltage,
overtemperature). Each pin requires an external pull-up resistor to VSTBY.
Bringing the slot’s ON[A/B] pin low resets /FAULT[A/B] if /FAULT[A/B] was
asserted in response to a fault condition on one of the slot’s MAIN outputs (5V,
3.3V, +12V, or –12V).
/FAULT[A/B] is reset by bringing the slot’s AUXEN[A/B] pin low if /FAULT[A/B]
was asserted in response to a fault condition on the slot’s VAUX output. If a fault
condition occurred on both the MAIN and VAUX[A/B] outputs of the same slot,
then both ON[A/B] and AUXEN[A/B] must be brought low to de-assert the
/FAULT[A/B] output.
General Purpose Inputs: The states of these two inputs are available by reading
the Common Status Register, Bits [4:5]. If not used, connect each pin to GND.
SMBus Address Select Pins: Connect to ground or leave open in order to 41 A0
program device SMBus base address. These inputs have internal pull-up
resistors to VSTBY[A/B].
SMBus Data: Bidirectional SMBus data line.
SMBus Clock: Input.
Interrupt Output: Open-drain, active-low. Asserted whenever a power fault is
detected if the INTMSK bit (CS Register Bit D[3]) is a logical "0". This output is
de-asserted by performing an "echo reset" to the appropriate fault bit(s) in the
STAT[A/B] and/or CS registers. This pin requires an external pull-up resistor to
V
IC Ground Connections: Tie directly to the system’s analog ground plane
directly at the device.
STBY
.
5
FLT
. t
FLT
is the amount of time for which a slot
M9999-092208
MIC2593