LDS8866002-T2-300 IXYS, LDS8866002-T2-300 Datasheet
LDS8866002-T2-300
Specifications of LDS8866002-T2-300
LDS8866-002-T2-2
LDS8866-002-T2-2
LDS8866002-T2-300-2
Related parts for LDS8866002-T2-300
LDS8866002-T2-300 Summary of contents
Page 1
... LEDs. Inclusion of a 1.33-x fractional charge pump mode and ultra low dropout TYPICAL APPLICATION CIRCUIT © 2009 IXYS Corp. Characteristics subject to change without notice PowerLite™ Current Regulator (PCR) increases device’ efficiency up to 94%. New mode requires no additional external capacitors ...
Page 2
... Thermal Shutdown 1 Thermal Hysteresis V Under Voltage Lockout (UVLO Threshold V Over Voltage Protection OUT 1 Sample test only © 2009 IXYS Corp. Characteristics subject to change without notice Rating 0.7V IN -65 to +160 -40 to +125 300 Rating 2.7 to 5.5 - 3.6V, Cin = Cout = 1 µ 0.22 µ High, T ...
Page 3
... PWM pins must be held low for more than 30 ms the charge pump output that is connected to OUT the LED anodes. A small 1μ F ceramic bypass © 2009 IXYS Corp. Characteristics subject to change without notice Function capacitor is required between the V μ F ground near the device ...
Page 4
... Power-Up in 1.33-x Mode Ch1 – PWM1, PWM2, Ch2 – Vout, Ch3 – Output current (100mA/div) Power-Up in 2-x Mode Ch1 – PWM1, PWM2, Ch2 – Vout, Ch3 – Output current (100mA/div) © 2009 IXYS Corp. Characteristics subject to change without notice = 0.22 μ 1μ 25° ...
Page 5
... Ch1 – PWM1, PWM2, Ch2 – Vout, Ch3 – Output current (100mA/div) Operating Waveforms at 50kHz PWM mode Ch1 – PWM1, PWM2, Ch2 – Vout, Ch3 – Output current (100mA/div) © 2009 IXYS Corp. Characteristics subject to change without notice = 0.22 μ 1μ 25° ...
Page 6
... If this voltage falls below 75 mV (typical) at any one channel, (channel with LED with highest forward voltage), the Mode Control Block changes charge pump mode to the next multiplication ratio. © 2009 IXYS Corp. Characteristics subject to change without notice Figure 2. LDS8866 Functional Block Diagram Charge Pump Output Resistance at given mode, Iout is sum of all LED currents, and charge pump’ ...
Page 7
... PWM1/PWM2 inputs, the LDS8866’s maximum input current is determined by the factory preset maximum LED current multiplied by number of LED used, the © 2009 IXYS Corp. Characteristics subject to change without notice The LDS8866’s PWM logic control circuits have been designed to operate from 100 Hz to 100 kHz with duty cycles higher than (0.02*F)% and lower than (100 – ...
Page 8
... A test current is placed in the channel to sense when the channel moves below V – 1.5 V. OUT Figure 4. Application circuit with 5 LEDs © 2009 IXYS Corp. Characteristics subject to change without notice Protection Modes The LDS8866 has follow protection modes 1. LED short ...
Page 9
... A copper area matching the TQFN exposed pad (TAB) must be connected to the ground plane underneath. The use of multiple via improves the package heat dissipation. © 2009 IXYS Corp. Characteristics subject to change without notice Figure 5. Recommended layout 9 Doc. No. 8866DS, Rev. N2.0 ...
Page 10
... L 0.325 0.375 m 0.150 typ n 0.225 typ Note: 1. All dimensions are in millimeters 2. Complies with JEDEC Standard MO-220 © 2009 IXYS Corp. Characteristics subject to change without notice MAX 0.80 0.05 0.228 0.30 3.05 1.75 3.05 1.75 0.425 10 Doc. No. 8866DS, Rev. N2.0 ...
Page 11
... The device used in the above example is a LDS8866 002–T2 ( 3x3 TQFN, Tape & Reel, 30/25/5 mA maximum current per LED bank). 4) For additional package and temperature options, please contact your nearest IXYS Corp. Sales office. © 2009 IXYS Corp. Characteristics subject to change without notice ...
Page 12
... IXYS Corp. products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the IXYS Corp. product could create a situation where personal injury or death may occur. ...