CAT3637HV3-GT2 ON Semiconductor, CAT3637HV3-GT2 Datasheet - Page 9

• Manufacturer Part Number: CAT3637HV3-GT2
• Description: IC LED DRVR WHITE BCKLGT 16-TQFN
• Manufacturer: ON Semiconductor
• Series: QUAD-Mode®r
• Type: Backlight, White LEDr

Specifications of CAT3637HV3-GT2

• Topology: Switched Capacitor (Charge Pump)
• Number Of Outputs: 6
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 600kHz ~ 1.4MHz
• Voltage - Supply: 2.5 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-TFQFN Exposed Pad
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 30mA
• Internal Switch(s): Yes
• Efficiency: 92%
• Number Of Segments: 6
• Operating Supply Voltage: 2.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Details
• Other names: CAT3637HV3-GT2TR

Pin Function
VIN is the supply pin for the charge pump. A small 1 mF
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is from 2.5 V to 5.5 V. Whenever the input supply falls
below the under−voltage threshold (2 V) all the LED
channels will be automatically disabled and the device
register are reset to default values.
EN/SET is the enable and one wire addressable control logic
input for all LED channels. Guaranteed levels of logic high
and logic low are set at 1.3 V and 0.4 V respectively. When
EN/SET is initially taken high, the device becomes enabled
and all LED currents remain at 0 mA. To place the device
into zero current mode, the EN/SET pin must be held low for
more than 1.5 ms.
VOUT is the charge pump output that is connected to the
LED anodes. A small 1 mF ceramic bypass capacitor is
required between the VOUT pin and ground near the device.
Table 5. PIN DESCRIPTION
13/14
Pin #
TAB
10
12
15
16
11
1
2
3
4
5
6
7
8
9
EN/SET
Name
VOUT
LED6
LED5
LED4
LED3
LED2
LED1
GND
C1+
C1−
C2+
C2−
TAB
VIN
NC
LED6 cathode terminal
LED5 cathode terminal
LED4 cathode terminal
LED3 cathode terminal
LED2 cathode terminal
LED1 cathode terminal
Charge pump output, connect to LED anodes
Charge pump input, connect to battery or supply
Bucket capacitor 1, positive terminal
Bucket capacitor 1, negative terminal
Bucket capacitor 2, positive terminal
Bucket capacitor 2, negative terminal
No connect
Ground reference
Device enable (active high) and 1 wire control input
Connect to GND on the PCB
http://onsemi.com
9
GND is the ground reference for the charge pump. The pin
must be connected to the ground plane on the PCB.
C1+, C1− are connected to each side of the ceramic bucket
capacitor C1.
C2+, C2− are connected to each side of the ceramic bucket
capacitor C2.
LED1 to LED6 provide the internal regulated current for
each of the LED cathodes. These pins enter high−impedance
zero current state whenever the device is placed in shutdown
mode.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
Function