MAX16802AEUA+ Maxim Integrated Products, MAX16802AEUA+ Datasheet - Page 9

• Manufacturer Part Number: MAX16802AEUA+
• Description: IC LED DRIVER HIGH BRIGHT 8-MSOP
• Manufacturer: Maxim Integrated Products
• Type: HBLED Driverr

Specifications of MAX16802AEUA+

• Constant Current: Yes
• Topology: Flyback, PWM, SEPIC, Step-Down (Buck), Step-Up (Boost)
• Number Of Outputs: 1
• Internal Driver: No
• Type - Primary: Backlight
• Type - Secondary: High Brightness LED (HBLED), RGB
• Frequency: 230kHz ~ 290kHz
• Voltage - Supply: 10.8 V ~ 24 V
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 3A
• Internal Switch(s): No
• Low Level Output Current: 500 uA (Min)
• High Level Output Current: 500 uA (Min)
• Operating Supply Voltage: 10.8 V to 24 V
• Maximum Supply Current: 1.4 mA
• Maximum Power Dissipation: 362 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Efficiency: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 3. V
MAX16801 in Bootstrapped Mode
the wake-up level of +23.6V. Once V
bootstrap UVLO threshold, NDRV begins switching the
MOSFET and transfers energy to the secondary and
tertiary outputs. If the voltage on the tertiary output
builds to a value higher than +9.7V (the bootstrap
UVLO lower threshold), then startup has been accom-
plished and sustained operation commences.
If V
the device goes back to low-current UVLO. In this
case, increase C1 in order to store enough energy to
allow for the voltage at the tertiary winding to build up.
Figure 4. Typical Current Soft-Start During Initial Startup
IN
drops below +9.7V before startup is complete,
0
0
IN
and V
CC
_______________________________________________________________________________________
During Startup when Using the
10ms/div
100ms/div
Offline and DC-DC PWM Controllers for
100mA/div
IN
V
2V/div
MAX16801
V
5V/div
CC
IN
exceeds the
PIN
High-Brightness LED Drivers
The MAX16801/MAX16802 soft-start feature allows the
LED current to ramp up in a controlled manner. Soft-
start begins after UVLO deasserts. The voltage applied
to the noninverting node of the amplifier ramps from 0
to +1.23V over a 60ms soft-start timeout period. Figure
4 shows a typical 0.5A output current during startup.
Note the staircase increase of the LED current. This is a
result of the digital soft-starting technique used. Unlike
other devices, the reference voltage to the internal
amplifier is soft-started. This method results in superior
control of the LED current.
The NDRV pin drives an external n-channel MOSFET.
The NDRV output is supplied by the internal regulator
(V
For the universal input voltage and applications with a
transformer, the MOSFET used must be able to with-
stand the DC level of the high-line input voltage plus
the reflected voltage at the primary of the transformer.
For most offline applications that use the discontinuous
flyback topology, this requires a MOSFET rated at
600V. NDRV can source/sink in excess of the
650mA/1000mA peak current. Select a MOSFET that
yields acceptable conduction and switching losses.
The MAX16801/MAX16802 include an internal error
amplifier that can be used to regulate the LED current
very accurately. For example, see the nonisolated
power supply in Figure 5. Calculate the LED current
using the following equation:
where V
input is internally connected to a digital soft-start circuit
that gradually increases the reference voltage during
startup and is applied to this pin. This forces the LED
current to come up in an orderly and well-defined man-
ner under all conditions.
CC
), which is internally set to approximately +9.5V.
REF
n-Channel MOSFET Switch Driver
= +1.23V. The amplifier’s noninverting
I
LED
Internal Error Amplifier
=
V
REF
R
7
Soft-Start
9