LT3756EUD-2#PBF Linear Technology, LT3756EUD-2#PBF Datasheet - Page 11
![IC LED DRVR HP CONST CURR 16-QFN](/photos/6/67/66790/161-16-qfn__sml.jpg)
LT3756EUD-2#PBF
Manufacturer Part Number
LT3756EUD-2#PBF
Description
IC LED DRVR HP CONST CURR 16-QFN
Manufacturer
Linear Technology
Type
High Power, Constant Currentr
Datasheet
1.LT3756EUD-1PBF.pdf
(24 pages)
Specifications of LT3756EUD-2#PBF
Constant Current
Yes
Constant Voltage
Yes
Topology
Flyback, Low Side, PWM, SEPIC, Step-Down (Buck), Step-Up (Boost)
Number Of Outputs
1
Internal Driver
No
Type - Primary
Automotive
Type - Secondary
White LED
Frequency
100kHz ~ 1MHz
Voltage - Supply
6 V ~ 100 V
Voltage - Output
100V
Mounting Type
Surface Mount
Package / Case
16-WQFN Exposed Pad
Operating Temperature
-40°C ~ 125°C
Current - Output / Channel
1A
Internal Switch(s)
Yes
Efficiency
94%
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
applicaTions inForMaTion
INTV
The INTV
and to store the charge for the large GATE switching cur-
rents. Choose a 10V rated low ESR, X7R or X5R ceramic
capacitor for best performance. A 4.7µF capacitor will be
adequate for many applications. Place the capacitor close
to the IC to minimize the trace length to the INTV
and also to the IC ground.
An internal current limit on the INTV
the LT3756 from excessive on-chip power dissipation.
The minimum value of this current should be considered
when choosing the switching NMOS and the operating
frequency.
I
Careful choice of a lower Q
ing frequencies, leading to smaller magnetics. The INTV
pin has its own undervoltage disable (UVLO) set to 4.1V
(typical) to protect the external FETs from excessive power
dissipation caused by not being fully enhanced. If the
INTV
and PWMOUT pins will be forced to 0V and the soft-start
pin will be reset.
If the input voltage, V
pin could be connected to the input supply. Be aware that
a small current (less than 12μA) will load the INTV
shutdown. If V
below the INTV
operating V
by the dropout voltage of the linear regulator and the 4.5V
(4.1V typical) INTV
mentioned above.
Programming the Turn-On and Turn-Off Thresholds
with the SHDN/UVLO Pin
The falling UVLO value can be accurately set by the resistor
divider. A small 2.1µA pull-down current is active when
SHDN/UVLO is below the threshold. The purpose of this
current is to allow the user to program the rising hysteresis.
INTVCC
I
INTVCC
CC
CC
can be calculated from the following equation:
Regulator Bypassing and Operation
pin drops below the UVLO threshold, the GATE
CC
= Q
IN
pin requires a capacitor for stable operation
G
will be close to 7V . This value is determined
IN
CC
• f
is normally above, but occasionally drops
OSC
regulation voltage, then the minimum
IN
CC
, will not exceed 8V, then the INTV
undervoltage lockout threshold
G
FET will allow higher switch-
CC
output protects
CC
CC
pin
CC
CC
in
LED Current Programming
The LED current is programmed by placing an appropriate
value current sense resistor, R
string. The voltage drop across R
by the ISP and ISN pins. Typically, sensing of the current
should be done at the top of the LED string. If this option
is not available, then the current may be sensed at the
bottom of the string, but take caution that the minimum
ISN value does not fall below 3V, which is the lower limit of
the LED current regulation function. The CTRL pin should
be tied to a voltage higher than 1.1V to get the full-scale
100mV (typical) threshold across the sense resistor. The
CTRL pin can also be used to dim the LED current to zero,
although relative accuracy decreases with the decreasing
voltage sense threshold. When the CTRL pin voltage is
less than 1.0V, the LED current is:
When the CTRL pin voltage is between 1V and 1.2V the LED
current varies with CTRL, but departs from the equation
above by an increasing amount as CTRL voltage increases.
Ultimately, above CTRL = 1.2V the LED current no longer
varies with CTRL. At CTRL = 1.1V, the actual value of I
is ~98% of the equation’s estimate.
The following equations should be used to determine the
values of the resistors:
I
V
V
LED
LT3756/LT3756-1/LT3756-2
IN,FALLING
IN,RISING
=
V
Figure 1. Resistor Connection to Set V
Undervoltage Shutdown Threshold
CTRL
R
= 2.1µA • R1+ V
= 1.22 •
LED
− 100mV
• 10
SHDN/UVLO
LT3756
R1+ R2
375612 F01
R2
IN,FALLING
LED
V
, in series with the LED
IN
LED
R1
R2
is (Kelvin) sensed
IN
375612fb
LED