LM3406HVMHX/NOPB National Semiconductor, LM3406HVMHX/NOPB Datasheet - Page 11

• Manufacturer Part Number: LM3406HVMHX/NOPB
• Description: IC LED DRVR HP CONS CURR 14TSSOP
• Manufacturer: National Semiconductor
• Series: PowerWise®r
• Type: High Power, Constant Currentr

Specifications of LM3406HVMHX/NOPB

• Constant Current: Yes
• Topology: PWM, Step-Down (Buck)
• Number Of Outputs: 1
• Internal Driver: Yes
• Type - Primary: Automotive
• Type - Secondary: White LED
• Frequency: 1MHz
• Voltage - Supply: 6 V ~ 75 V
• Mounting Type: Surface Mount
• Package / Case: 14-TSSOP Exposed Pad, 14-eTSSOP 14-HTSSOP
• Operating Temperature: -40°C ~ 125°C
• Current - Output / Channel: 1.5A
• Internal Switch(s): Yes
• Efficiency: 96%
• For Use With: 876-1003 - LM3406 LED DRIVER EVAL BOARDLM3406MHEVAL - BOARD EVAL FOR LM3406MH
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Other names: LM3406HVMHX

www.national.com
PEAK CURRENT LIMIT
The current limit comparator of the LM3406/06HV will engage
whenever the power MOSFET current (equal to the inductor
current while the MOSFET is on) exceeds 2.1A (typical). The
power MOSFET is disabled for a cool-down time that of ap-
proximately 100 µs. At the conclusion of this cool-down time
the system re-starts. If the current limit condition persists the
cycle of cool-down time and restarting will continue, creating
a low-power hiccup mode, minimizing thermal stress on the
LM3406/06HV and the external circuit components.
OVER-VOLTAGE/OVER-CURRENT COMPARATOR
The CS pin includes an output over-voltage/over-current
comparator that will disable the power MOSFET whenever
V
for the output current. Output current overshoot is limited to
300 mV / R
OCP comparator limits the maximum ripple voltage at the CS
pin to 200 mV
SNS
exceeds 300 mV. This threshold provides a hard limit
SNS
P-P
by this comparator during transients. The OVP/
.
FIGURE 3. Dimming with a Parallel FET
10
OUTPUT OPEN-CIRCUIT
The most common failure mode for power LEDs is a broken
bond wire, and the result is an output open-circuit. When this
happens the feedback path is disconnected, and the output
voltage will attempt to rise. In buck converters the output volt-
age can only rise as high as the input voltage, and the
minimum off-time requirement ensures that V
less than V
Z1, and zener limiting resistor, R
the reverse breakdown voltage of Z1 plus 200 mV. The zener
diode reverse breakdown voltage, V
the maximum combined V
imum recommended value for R
The output stage (SW and VOUT pins) of the LM3406/06HV
is capable of withstanding V
output capacitor is rated to handle the full input voltage. When
an LED fails open-circuit and there is no output capacitor
present the surge in output voltage due to the collapsing mag-
netic field in the output inductor can exceed V
damage the LM3406/06HV IC. As an alternative to the zener
clamp method described previously, a diode can be connect-
ed from the output to the input of the regulator circuit that will
clamp the inductive surge to one V
Regardless of which protection method is used a resistance
in series with the VOUT pin, R
the current in the event the VOUT pin is pulled below ground
when the LED circuit is reconnected. This can occur frequent-
ly if the lead lengths to the LEDs are long and the inductance
is significant. A resistor between 1 kΩ and 10 kΩ is recom-
mended.
IN
.
Figure 4
shows a method using a zener diode,
F
of all LEDs in the array. The max-
O(MAX)
OUT
Z
Z
is 1 kΩ.
, to limit output voltage to
, is recommended to limit
indefinitely as long as the
D
Z
above V
, must be greater than
30020327
O(MAX)
IN
.
IN
is slightly
and can