MAX1986ETE+T Maxim Integrated Products, MAX1986ETE+T Datasheet - Page 8

• Manufacturer Part Number: MAX1986ETE+T
• Description: IC LED DRVR WHITE BCKLGT 16-TQFN
• Manufacturer: Maxim Integrated Products
• Type: Backlight, White LEDr

Specifications of MAX1986ETE+T

• Topology: PWM, Step-Up (Boost)
• Number Of Outputs: 4
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 800kHz ~ 1.2MHz
• Voltage - Supply: 2.7 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 16-TQFN Exposed Pad
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 25mA
• Internal Switch(s): Yes
• Efficiency: 90%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Details

Ultra-High-Efficiency White
LED Drivers
8
MAX1984 MAX1985 MAX1986
_______________________________________________________________________________________
—
10
11
12
13
14
15
1
2
3
4
5
6
7
8
9
4, 12
PIN
10
11
—
—
13
14
15
1
2
3
5
6
7
9
8
—
—
—
—
—
10
11
1
2
3
4
5
7
8
6
9
NAME
GND
BITB
OUT
N.C.
LDG
SETI
LD1
LD2
LD3
LD4
LD5
LD6
LD7
LD8
REF
LX
Inductor Connection. LX is connected to the drains of the internal N-channel and
P-channel MOSFETs.
Ground
No Connection. Not internally connected.
LED1 Cathode Connection. LD1 is the open-drain output of an internal current
regulator for controlling the current through LED1. It is able to sink up to 25mA.
If not used, connect LD1 to GND.
LED2 Cathode Connection. LD2 is the open-drain output of an internal current
regulator for controlling the current through LED2. It is able to sink up to 25mA.
If not used, connect LD2 to GND.
LED3 Cathode Connection. LD3 is the open-drain output of an internal current
regulator for controlling the current through LED3. It is able to sink up to 25mA.
If not used, connect LD5 to GND.
LED4 Cathode Connection. LD4 is the open-drain output of an internal current
regulator for controlling the current through LED4. It is able to sink up to 25mA.
If not used, connect LD4 to GND.
Common Ground Connection for Internal Current Regulators. Connect LDG to
GND.
LED5 Cathode Connection. LD5 is the open-drain output of an internal current
regulator for controlling the current through LED5. It is able to sink up to 25mA.
If not used, connect LD5 to GND.
LED6 Cathode Connection. LD6 is the open-drain output of an internal current
regulator for controlling the current through LED6. It is able to sink up to 25mA.
If not used, connect LD6 to GND.
LED7 Cathode Connection. LD7 is the open-drain output of an internal current
regulator for controlling the current through LED7. It is able to sink up to 25mA.
If not used, connect LD7 to GND.
LED8 Cathode Connection. LD8 is the open-drain output of an internal current
regulator for controlling the current through LED8. It is able to sink up to 25mA.
If not used, connect LD8 to GND.
Maximum LED Current Set Input. SETI sets the maximum current through each
LED. Connect SETI to IN for a default maximum current of 18mA; connect SETI to
GND for the 0.5mA LED test mode. Connect a resistor from SETI to GND to adjust
the maximum current between 12mA to 25mA (see the Setting the Maximum LED
Current section).
1.25V Reference Output. Bypass REF to GND with a minimum 0.22µF ceramic
capacitor.
Brightness Control Input (Multimode):
Step-Up Regulator Output. Bypass OUT to GND with a 4.7µF capacitor.
DPWM Mode: Leave unconnected for greater than 50kHz operation. Add a
capacitor from BITB to ground for lower frequency operation.
Analog Mode: Analog control signal input.
2- or 3-Bit Parallel Mode: Digital input. Least significant bit (LSB) for 2-bit mode.
FUNCTION
Pin Description