MIC2293-15BML TR Micrel Inc, MIC2293-15BML TR Datasheet
MIC2293-15BML TR
Specifications of MIC2293-15BML TR
Related parts for MIC2293-15BML TR
MIC2293-15BML TR Summary of contents
Page 1
... MIC2292/93 General Description The MIC2292 and MIC2293 are high frequency, Pulse Width Modulator (PWM) boost regulators optimized for constant- current, white LED driver applications. Because of their constant PWM switching frequencies of 1.6MHz and 2MHz, respectively, the MIC2292/93 can use the smallest external components, allowing designers to avoid sensitive IF bands in their RF applications ...
Page 2
... MIC2292/93 Ordering Information Marking Part Number Code MIC2292-15BML SWA MIC2292-15YML SWA MIC2292-34BML SWC MIC2292-34YML SWC MIC2293-15BML SZA MIC2293-15YML SZA MIC2293-34BML SZC MIC2293-34YML SZC Pin Configuration Pin Description Pin Number Pin Name 1 OUT 2 VIN 4,8 GND EP GND M9999-091509 Overvoltage Protection Frequency Temp. Range 15V 1 ...
Page 3
... FB 3V ≤ V ≤ 5mA ≤ I ≤ 20mA OUT 10V EN SW TURN ON TURN OFF V = 10V EN MIC2292 MIC2293 I = 150mA 30V R MIC2292/93-15 MIC2292/93-34 Hysteresis , and the ambient temperature The maximum allowable power dissipation will result in excessive Micrel, Inc. (2) ) ..........................................2.5V to 10V IN ) .......................................V OUT IN ) ............ – ...
Page 4
... L = 10µ 1µF OUT (mA) OUT Quiescent Current vs. Input Voltage (V) IN Schottky Forward Voltage Drop 700 600 500 400 300 200 100 0 SCHOTTKY FORWARD VOLTAGE DROP (mV) M9999-091509 MIC2293 3 Series LED Efficiency 10µ 1µF OUT (mA) LED Feedback Voltage vs. Input Voltage 100 ...
Page 5
MIC2292/93 Switch Frequency vs. Temperature 2 1.6 1.2 0.8 0 120 TEMPERATURE (°C) M9999-091509 Switch Saturation Voltage vs. Current 600 500 400 V = 2.5V IN 300 200 100 0 0 ...
Page 6
... Schottky rectifier diode. The oscillator generates a 1.6MHz clock for the MIC2292 and a 2.0MHz clock for the MIC2293. The clocks' two functions are to trigger the PWM generator that turns on the output transistor and to reset the slope compensation ramp generator ...
Page 7
MIC2292/93 External Component Selection The MIC2292/93 can be used across a wide rage of applica- Series LEDs 2 22µH 15µH 10µH 6.8µH 4.7µH 3 22µH 15µH 10µH 6.8µH 4.7µH 4 22µH 15µH 10µH 6.8µH 4.7µ 22µH 15µH 10µH ...
Page 8
MIC2292/93 Dimming Control There are two techniques for dimming control. One is PWM dimming and the other is continuous dimming. 1. PWM dimming control is implemented by applying a PWM signal on EN pin as shown in Figure 1. The ...
Page 9
MIC2292/93 Functional Characteristics 6-Series LED Circuit with External Soft-Start TIME (100µs/ M9999-091509 6-Series LED Circuit without External Soft-Start L = 10µ 1µ 0.22µF OUT 20mA OUT 6 ...
Page 10
... MIC2292/93 Package Information MICREL INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 tel This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. ...