NCP5009DMR2 ON Semiconductor, NCP5009DMR2 Datasheet
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
NCP5009DMR2
Specifications of NCP5009DMR2
Available stocks
Related parts for NCP5009DMR2
NCP5009DMR2 Summary of contents
Page 1
... Tape & Reel Micro 10 NCP5008DMR2G 4000 / Tape & Reel (Pb−Free) 4000 / Tape & Reel NCP5009DMR2 Micro 10 †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Publication Order Number: ...
Page 2
BACK LIGHT WHITE LED CURRENT DRIVE CONTROLLER BandGap VBIAS 4 CLK bat V bat Q2 POR LOCAL ref PHOTO 2 (See Note) V bat + − GND NOTE: This functionality is NOT implemented ...
Page 3
PIN FUNCTION DESCRIPTION Pin Symbol Type 1 I INPUT This pin provides the output current range adjustment by means of a resistor connected to ref ground. The current output tolerance depends upon the accuracy of this resistor. Using a "1% ...
Page 4
Table 1. Shift Register Bits Assignment and Functions SetReg shift register (Note: The register content is latched upon CS positive going Value After POR 0 Iout Peak (mA) I *k*7.5 ref LOCAL CLOCK ...
Page 5
POWER SUPPLY SECTION (−25°C to +85°C ambient temperature, unless otherwise noted.) Rating Power Supply Power Supply Threshold Startup Voltage Output Load Voltage Compliance Pulsed Current Regulation Range Continuous DC Current in the Load = 3 mH/0.71 ...
Page 6
TYPICAL OPERATING CHARACTERISTICS Condition: Typical Application mH, Cin = 10 mF, Cout = 2.2 mF 3.0 V bat ...
Page 7
TYPICAL OPERATING CHARACTERISTICS Condition: Typical Application mH, Cin = 10 mF, Cout = 2.2 mF ...
Page 8
TYPICAL OPERATING CHARACTERISTICS Condition: Typical Application mH, Cin = 10 mF, Cout = 2.2 mF (mA) LED Figure 15. Efficiency ...
Page 9
Remote Control Programming Sequence CS CLEAR CLK Qdata Output Current Programmed Register I out ref Internal Latch Data and Reset Iout Upon CS transition from High to Low, the internal sequence will take ...
Page 10
Set Up Output Current Range V bat 1 V bat + − GND I ref V bat R ref 30 k GND 1 V bat + − GND Photo Q1 NPN−PHOTO GND The current sunk to ground on PHOTO pin ...
Page 11
DC/DC Converter Operation The DC/DC converter operates with a boost structure depicted in Figure 21, the load being supplied by the pulsed current coming from the external inductor L1. The current V bat + I peak_ref U2 − V bat ...
Page 12
Output Load Drive In order to make profit of the built−in Boost capabilities, one shall operate the NCP5008/NCP5009 in the continuous output current mode. Such a mode is achieved by using and external reservoir capacitor (preferably a low ESR ceramic ...
Page 13
NCP5008, NCP5009 ref PHOTO GND Vcc Q1 V bat NPN−PHOTO GND 4 4 VBIAS CLK NCP5009 GND Figure 23. Typical Semi−Pulsed Mode of Operation in REMOTE Mode ...
Page 14
NCP5008, NCP5009 DAC ref PHOTO Q1 V bat NPN−PHOTO GND 4 4 VBIAS OFF CLK NCP5009 D1 LED GND Figure 25. DAC Current Control Mode Operation in LOCAL Mode ...
Page 15
... TYPICAL LEDS LOAD MAPPING LED LED LED LED LED LED Example Load 10.4 V LED LED D4 D6 LED LED = 3 Condition: V bat Manufacturer ON Semiconductor MURATA MURATA MURATA Osram Osram http://onsemi.com LED LED D8 D10 LED LED D1 D4 LED LED D2 D5 LED LED D3 D6 LED LED Example 3 ...
Page 16
LAYOUT EXAMPLE The Figure 28 represents the typical printed circuit layout based on the basic application Figure 1. This application has been routed on a single copper layer to save cost. A dual side PCB has better noise protection and ...
Page 17
... SEATING H PLANE *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein ...