L9822EPD STMicroelectronics, L9822EPD Datasheet - Page 7

• Manufacturer Part Number: L9822EPD
• Description: IC DRIVER SOLENOID OCT POWERSO20
• Manufacturer: STMicroelectronics
• Type: Low Sider

Specifications of L9822EPD

• Input Type: SPI
• Number Of Outputs: 8
• On-state Resistance: 550 mOhm
• Current - Peak Output: 1.05A
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: PowerSO-20 Exposed Bottom Pad
• Rise Time: 50 ns
• Fall Time: 50 ns
• Supply Voltage (min): - 0.7 V
• Supply Current: 10 mA
• Maximum Operating Temperature: + 150 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Number Of Drivers: 8
• Driver Configuration: Inverting
• Driver Type: Low Side
• Frequency (max): 2MHz
• Operating Supply Voltage (max): 7V
• Peak Output Current: 1.05A
• Operating Supply Voltage (min): -0.7V
• Operating Supply Voltage (typ): 5V
• Turn Off Delay Time: 10us
• Turn On Delay Time (max): 10us
• Operating Temp Range: -40C to 150C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 20
• Package Type: PowerSO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output / Channel: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

L9822E
2.1
Pin description
Table 2.
PowerSO20
1, 10, 11, 20
5-8, 13-16
pin #
9,12
17
18
19
2
3
4
Pin function
Multiwatt15
1-4, 12-15
pin #
10
11
8
9
5
6
7
-
OUTPUT
RESET
Name
SCLK
GND
N.C.
V
SO
1-7
CE
SI
CC
Device ground.
This ground applies for the logic circuits as well as the
power output stages.
Serial output.
This pin is the serial output from the shift register and it is
tri-stated when CE is high. A high for a data bit on this pin
indicates that the particular output is high. A low on this
pin for a data bit indicates that the output is low.
Comparing the serial output bits with the previous serial
input bits the external microcontroller implements the
diagnostic data supplied by the L9822E.
Logic supply voltage - nominally 5V.
Asynchronous reset for the output stages, the parallel
latch and the shift register inside the
active low and it must not be left floating. A power on clear
function may be implemented connecting this pin to VCC
with an external resistor and to ground with an external
capacitor.
Power output pins.
The input and output bits corresponding to 07 are sent
and received first via the SPI bus and 00 is the last. The
outputs are provided with current limiting and voltage
sense functions for fault indication and protection. The
nominal load current for these outputs is 500mA, but the
current limiting is set to a minimum of 1.05A.
The outputs also have on board clamps set at about 36V
for recirculation of inductive load current.
Pins not connected.
Chip enable.
Data is transferred from the shift registers to the outputs
on the rising edge of this signal. The falling edge of this
signal sets the shift register with the output voltage sense
bits coming from the output stages. The output driver for
the SO pin is enabled when this pin is low.
Serial clock.
This pin clocks the shift register. New SO data will appear
on every rising edge of this pin and new SI data will be
latched on every SCLK’s falling edge into the shift
register.
Serial input.
This pin is the serial data input. A high on this pin will
program a particular output to be OFF, while a low will
turn it ON.
Function
L9822E
Pin description
. This pin is
7/17