MAX4896ETP+T Maxim Integrated Products, MAX4896ETP+T Datasheet
MAX4896ETP+T
Specifications of MAX4896ETP+T
Related parts for MAX4896ETP+T
MAX4896ETP+T Summary of contents
Page 1
... SCLK CS MAX4896 DIN DOUT SLPD GND Pin Configuration appears at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. Supports Up to 50V Continuous Drain-to-Source Voltage Guaranteed Drive Current ...
Page 2
Space-Saving, 8-Channel Relay/Load Driver ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND.) V ......................................................................... -0.3V to +7.0V S OUT_ ....................................................................(-0.3V to +50V) Continuous OUT_ Voltage ...................................................+50V CS, SCLK, DIN, RESET, SPLD, PDCD ..................-0.3V to +7.0V DOUT ............................................................-0. PGND ...
Page 3
Space-Saving, 8-Channel Relay/Load Driver ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V -40°C to +125°C, unless otherwise noted. Typical values are PARAMETER SYMBOL OUT Clamping Voltage V CLAMP OUT Current-Limit Threshold I LIM OUT ...
Page 4
Space-Saving, 8-Channel Relay/Load Driver ELECTRICAL CHARACTERISTICS (continued +2.7V to +5.5V -40°C to +125°C, unless otherwise noted. Typical values are PARAMETER SYMBOL SCLK Frequency f SCLK Cycle Time ...
Page 5
Space-Saving, 8-Channel Relay/Load Driver (T = +25°C, unless otherwise noted.) A QUIESCENT CURRENT vs. SUPPLY VOLTAGE 12 ALL LOGIC INPUTS = +85° +125° ...
Page 6
Space-Saving, 8-Channel Relay/Load Driver (T = +25°C, unless otherwise noted.) A TURN-ON/TURN-OFF DELAY TIME vs. SUPPLY VOLTAGE 3 15V R = 300Ω L OUT C = 50pF L 2.5 2.0 t OFF 1.5 1 0.5 0 ...
Page 7
Space-Saving, 8-Channel Relay/Load Driver PIN NAME Reset Input. Drive RESET low to clear all latches and registers (all outputs are turned off). All OUT RESET 1 pulldown currents are disabled when RESET = low. Chip Select Input. Drive CS low ...
Page 8
Space-Saving, 8-Channel Relay/Load Driver Detail Description The MAX4896 is an 8-channel relay and load driver for medium voltage applications up to 50V. The MAX4896 features built-in inductive kickback protection, drive for latching/nonlatching, or dual-coil relays and an internal register for ...
Page 9
Space-Saving, 8-Channel Relay/Load Driver Table 1. Serial-Input Address DIN D0 D1 OUT_ OUT1 OUT2 Table 2. Serial-Output Address DOUT DO0 DO1 OUT_ OUT1 OUT2 Table 3. Status-Register Output Diagnostic OUTPUT DO_ STATUS STATUS BIT Off Low Normal operation. Fault condtion. ...
Page 10
Space-Saving, 8-Channel Relay/Load Driver The minimum fault-filtering time helps mask short-dura- tion fault conditions, such as driving highly capacitive loads. The typical diagnostics software routine works as follows: • Write data to the MAX4896 • Wait for t maximum to ...
Page 11
Space-Saving, 8-Channel Relay/Load Driver DEVICE 1 DIN DIN SCLK SCLK CS CS Figure 3. Daisy-Chain Configuration RESET SPI/CONTROL INTERFACE DIN DOUT SCLK CS FLAG ______________________________________________________________________________________ V S 0.1μF DEVICE DIN DOUT MAX4896 OUT1 SCLK OUT8 CS GND ...
Page 12
Space-Saving, 8-Channel Relay/Load Driver Pin Configuration TOP VIEW PGND 16 OUT2 17 OUT1 18 MAX4896 *EP + FLAG TQFN 5mm x 5mm *EXPOSED PADDLE. CONNECT TO PGND. 12 ...
Page 13
Space-Saving, 8-Channel Relay/Load Driver (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ Package Information 13 ...
Page 14
Space-Saving, 8-Channel Relay/Load Driver (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 14 ______________________________________________________________________________________ Package Information (continued) ...
Page 15
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 15 © 2007 Maxim Integrated Products DESCRIPTION is a registered trademark of Maxim Integrated Products, Inc ...