VND600 STMicroelectronics, VND600 Datasheet - Page 17
![RELAY SSR 2CHAN HI SIDE 16SOIC](/photos/7/44/74402/vnd600_sml.jpg)
VND600
Manufacturer Part Number
VND600
Description
RELAY SSR 2CHAN HI SIDE 16SOIC
Manufacturer
STMicroelectronics
Type
High Sider
Datasheet
1.VND60013TR.pdf
(26 pages)
Specifications of VND600
Input Type
Non-Inverting
Number Of Outputs
2
On-state Resistance
35 mOhm
Current - Peak Output
40A
Voltage - Supply
5.5 V ~ 36 V
Operating Temperature
-40°C ~ 150°C
Mounting Type
Surface Mount
Package / Case
16-SOIC (0.300", 7.5mm Width)
Switch Type
High Side
Mounting
Surface Mount
Operating Temperature (min)
-40C
Operating Temperature (max)
150C
Operating Temperature Classification
Automotive
Pin Count
16
Power Dissipation
8.3W
Load Current Rating
25 A
Relay Type
Solid State
Termination Style
Solder Leads
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Current - Output / Channel
-
Lead Free Status / Rohs Status
Not Compliant
Other names
497-4497-5
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
VND600PEP-E
Manufacturer:
st
Quantity:
1 564
Part Number:
VND600PEP13TR
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
VND600PEPTR-E
Manufacturer:
st
Quantity:
1 564
Part Number:
VND600PEPTR-E
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
VND600SP
Manufacturer:
ST
Quantity:
5 510
VND600
3.1.2
3.2
3.3
Solution 2: diode (D
A resistor (R
inductive load.
This small signal diode can be safely shared amongst several different HSDs. Also in this
case, the presence of the ground network will produce a shift (≈ 600mV) in the input
threshold and in the status output values if the microprocessor ground is not common to the
device ground. This shift will not vary if more than one HSD shares the same diode/resistor
network.
Series resistor in INPUT and STATUS lines are also required to prevent that, during battery
voltage transient, the current exceeds the absolute maximum rating.
Safest configuration for unused INPUT and STATUS pin is to leave them unconnected.
Load dump protection
D
V
that are greater than the ones shown in the ISO 7637-2: 2004(E) table.
MCU I/Os protection
If a ground protection network is used and negative transient are present on the V
the control pins will be pulled negative. ST suggests to insert a resistor (R
prevent the µC I/Os pins to latch-up.
The value of these resistors is a compromise between the leakage current of µC and the
current required by the HSD I/Os (Input levels compatibility) with the latch-up limit of µC
I/Os.
-V
Calculation example:
For V
5kΩ ≤ R
Recommended values: R
CC
ld
CCpeak
is necessary (Voltage Transient Suppressor) if the load dump peak voltage exceeds the
max DC rating. The same applies if the device is subject to transients on the V
CCpeak
prot
/I
latchup
≤ 65kΩ .
= - 100V and I
GND
≤ R
= 1kΩ) should be inserted in parallel to D
prot
≤ (V
prot
GND
OH
latchup
µ
=10kΩ .
C
) in the ground line
-V
≥ 20mA; V
IH
-V
GND
) / I
OH
IHmax
µ
C
≥ 4.5V
GND
if the device drives an
Application information
prot
) in line to
CC
CC
line,
line
17/26