L6229D STMicroelectronics, L6229D Datasheet - Page 14

• Manufacturer Part Number: L6229D
• Description: IC MOTOR DRIVER 3PHASE 24-SOIC
• Manufacturer: STMicroelectronics
• Type: Driverr

Specifications of L6229D

• Applications: DC Motor Driver, Brushless (BLDC), 3 Phase
• Number Of Outputs: 1
• Current - Output: 2.8A
• Voltage - Supply: 12 V ~ 52 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Operating Temperature Classification: Automotive
• Package Type: SO
• Operating Supply Voltage (min): 12V
• Operating Supply Voltage (max): 52V
• Operating Supply Voltage: 8 V to 52 V
• Supply Current: 1.4 A
• Mounting Style: SMD/SMT
• Motor Type: Three Phase DC Brushless
• No. Of Outputs: 3
• Output Current: 3.55A
• Output Voltage: 52V
• Supply Voltage Range: 8V To 52V
• Driver Case Style: SO
• No. Of Pins: 24
• Rohs Compliant: Yes
• For Use With: 497-5491 - EVAL BOARD FOR L6229PD SOIC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Load: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 497-5839-5; L6229D

L6229
Figure 16. 60° Hall Sensor Sequence.
3.6 TACHO
A tachometer function consists of a monostable, with constant off time (t
signal (H
18. For component values refer to Application Information section.
The monostable output drives an open drain output pin (TACHO). At each rising edge of the Hall Effect Sensors
H
t
to the pin RCPULSE. Figure 19 gives the relation between t
where C
By connecting the tachometer pin to an external pull-up resistor, the output signal average value V
tional to the frequency of the Hall Effect signal and, therefore, to the motor speed. This realizes a simple Fre-
quency-to-Voltage Converter. An op amp, configured as an integrator, filters the signal and compares it with a
reference voltage V
Figure 17. Tacho Operation Waveforms.
14/25
PULSE
1
, the monostable is triggered and the MOSFET connected to pin TACHO is turned off for a constant time
= H
t
PULSE
V
(see Figure 17). The off time t
M
H
PUL
1
3
1
). It allows developing an easy speed control loop by using an external op amp, as shown in Figure
=
should be chosen in the range 1nF … 100nF and R
= 0.6 · R
t
----------------- - V
P UL SE
= L
T
H
H
1
2
REF
⋅
PUL
, which sets the speed of the motor.
DD
· C
H
3
2
V
PUL
TACHO
H
H
H
V
M
1
2
3
H
H
1
2
PULSE
can be set using the external RC network (R
H
3b
t
3
PULSE
H
H
V
T
1
2
DD
PULSE
H
3
4
PUL
and C
in the range 20KΩ … 100KΩ.
H
H
1
2
PULSE
PUL
, R
), whose input is one Hall Effect
PUL
H
5
3
. We have approximately:
H
H
PUL
1
2
, C
PUL
H
6b
) connected
M
3
is propor-
H
H
1
2