LTC4416EMS#TRPBF Linear Technology, LTC4416EMS#TRPBF Datasheet
LTC4416EMS#TRPBF
Specifications of LTC4416EMS#TRPBF
Available stocks
Related parts for LTC4416EMS#TRPBF
LTC4416EMS#TRPBF Summary of contents
Page 1
... Logic Controlled Power Switch ■ Battery Backup System ■ Emergency Systems with Battery Backups ■ , LT, LTc and LTM are registered trademarks of Linear Technology corporation. PowerPath is a trademark of Linear Technology corporation. All other trademarks are the property of their respective owners. TYPICAL APPLICATIO U Automatic PowerPath Switchover V1 = 12V (FAIL ...
Page 2
LTC4416/LTC4416-1 ABSOLUTE AXI U RATI (Note 1) Supply Voltage (V1, V2) .............................. –14V to 40V Voltage from ....................... –40V to 40V S Input Voltage E1, E2 .................................................... –0.3V to 40V V ...
Page 3
ELECTRICAL CHARACTERISTICS temperature range, otherwise specifications are at T positive and current out of a pin is negative. All voltages are referenced to GND, unless otherwise specified. SYMBOL PARAMETER G1, G2 Controller GATE Active Forward Regulation I Source Current G(SRC) ...
Page 4
LTC4416/LTC4416-1 TYPICAL PERFOR A CE CHARACTERISTICS Temperature and Supply FR Voltage 40 35 –40°C 27°C 30 125° SUPPLY VOLTAGE (V) 4416 G01 V1, V2 and ...
Page 5
PI FU CTIO (Pin 1): Open-Drain Comparator Output of the E1 Pin > the H1 pin will go high impedance, otherwise REF the pin will be grounded. The maximum voltage permitted ...
Page 6
LTC4416/LTC4416-1 BLOCK DIAGRA GND OPERATIO U Operation can best be understood by referring to the Block Diagram which illustrates the internal circuit blocks. The LTC4416/LTC4416-1 ...
Page 7
OPERATIO U The band-gap reference provides internal bias currents used by the channel 1 and channel 2 controllers. It also provides a precision voltage reference, V parators C1 and C2. The band-gap reference is powered as long as a minimum ...
Page 8
LTC4416/LTC4416-1 OPERATIO Greater Than V2 Operation When V is below the V threshold, channel REF a “soft-off mode”. This means that G1 will only provide an I current instead G(SRC) ...
Page 9
APPLICATIO S I FOR ATIO U U This configuration would be used where 12V power supply and the V2 power supply is a 4-cell Li-Ion battery pack. When V1 is 12V, E2 disables the V2 source from ...
Page 10
LTC4416/LTC4416-1 APPLICATIO S I FOR ATIO U U differ by more than 100mV, 100% of the load will come from the higher V2. The user has the option of using E1 and E2 to disable one of ...
Page 11
... Figure 7. LTC4416-1 Configured for Overvoltage Protection Information furnished by Linear Technology corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 12
... Low Loss PowerPath Controller in MSOP LTC4413 Dual 2.6A, 2.5V to 5.5V Ideal Diodes in 3mm × 3mm DFN LTC4414 36V, Low Loss PowerPath Controller for Large PFETs ThinSOT is a trademark of Linear Technology Corporation. Linear Technology Corporation 1630 Mccarthy Blvd., Milpitas, cA 95035-7417 (408) 432-1900 FAX: (408) 434-0507 ● ...