MIC2025-1YM Micrel Inc, MIC2025-1YM Datasheet - Page 10
![IC SW DISTRIBUTION 1CHAN 8SOIC](/photos/6/50/65078/576-8-soic_sml.jpg)
MIC2025-1YM
Manufacturer Part Number
MIC2025-1YM
Description
IC SW DISTRIBUTION 1CHAN 8SOIC
Manufacturer
Micrel Inc
Series
MM8™r
Type
High Side Switchr
Datasheet
1.MIC2075-2YM.pdf
(14 pages)
Specifications of MIC2025-1YM
Current Limit
700mA
Number Of Outputs
1
Rds (on)
140 mOhm
Internal Switch(s)
Yes
Voltage - Input
2.7 ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Power Load Switch Type
High Side
Input Voltage
5.5V
On State Resistance
0.09ohm
Thermal Protection
Yes
On / Enable Input Polarity
Active High
No. Of Outputs
1
Short Circuit Current Limit
700mA
Input Voltage Range
2.7 to 5.5V
Number Of Switches
Single
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Package Type
SOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
576-1057
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MIC2025-1YM
Manufacturer:
MICREL
Quantity:
1 325
Company:
Part Number:
MIC2025-1YM
Manufacturer:
MICREL
Quantity:
5 000
Company:
Part Number:
MIC2025-1YM
Manufacturer:
MIC
Quantity:
82
Part Number:
MIC2025-1YM
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Company:
Part Number:
MIC2025-1YM TR
Manufacturer:
MAXIM
Quantity:
6
Part Number:
MIC2025-1YM-TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MIC2025-1YMM
Manufacturer:
MICREL
Quantity:
863
Part Number:
MIC2025-1YMM
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Part Number:
MIC2025-1YMM-TR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
MIC2025-1YMTR
Manufacturer:
MICREL/麦瑞
Quantity:
20 000
Short-Circuit Applied to Enabled Output
When a heavy load or short-circuit is applied, a large transient
current may flow until the current-limit circuitry responds. Once
this occurs the device limits current to less than the short-cir-
cuit current limit specification. See the Short-Circuit Transient
Response graph under Functional Characteristics.
Current-Limit Response—Ramped Load
The MIC2025/75 current-limit profile exhibits a small foldback
effect of about 200mA. Once this current-limit threshold is
exceeded the device switches into a constant current mode.
It is important to note that the device will supply current until
the current-limit threshold is exceeded. See the Current-Limit
Response graph under Functional Characteristics.
MIC2025/2075
V
I
LIMIT
V
V
I
I
V
V
I
LIMIT
I
OUT
OUT
OUT
D C
F L G
V
OUT
E N
I
F L G
DC
E N
Figure 1. MIC2075-2 Timing: Output Reset by Removing Load
Thermal Shutdow n
Thermal Shutdow n
Reached
Reached
Figure 2. MIC2025-2 Timing
Short-Circuit Faul t
Short-Circuit Faul t
t
t
D
D
10
Load/Fault
Removed
Fault Flag
The FLG signal is an N-channel open-drain MOSFET output.
FLG is asserted (active-low) when either an overcurrent
or thermal shutdown condition occurs. In the case where
an overcurrent condition occurs, FLG will be asserted only
after the flag response delay time, t
ensures that FLG is asserted only upon valid overcurrent
conditions and that erroneous error reporting is eliminated.
For example, false overcurrent conditions can occur during
hot-plug events when a highly capacitive load is connected
and causes a high transient inrush current that exceeds the
current-limit threshold. The FLG response delay time t
typically 3ms.
Undervoltage Lockout
Undervoltage lockout (UVLO) prevents the output MOS-
FET from turning on until V
Undervoltage detection functions only when the switch is
enabled.
Load Removed
(Output Reset)
IN
exceeds approximately 2.5V.
D
, has elapsed. This
June 2010
D
is