MIC2536-1BMM TR Micrel Inc, MIC2536-1BMM TR Datasheet
MIC2536-1BMM TR
Specifications of MIC2536-1BMM TR
MIC2536-1BMMTR
Related parts for MIC2536-1BMM TR
MIC2536-1BMM TR Summary of contents
Page 1
... Universal Serial Bus (USB) applications. Few exter- nal components are necessary to satisfy USB requirements. Each switch channel of the MIC2536 will supply up to 100mA as required for USB bus-powered downstream devices. Fault current is limited to typically 275mA by fast-acting current- limit circuitry which minimizes voltage droop on the upstream port during fault conditions ...
Page 2
... Pin Configuration Pin Description Pin Number Pin Name 1 ENA 2 FLGA 3 FLGB 4 ENB 5 OUTB 6 GND OUTA MIC2536 Enable Temperature Range Active High – +85 C Active Low – +85 C Active High – +85 C Active Low – +85 C MIC2536-x ENA OUTA 1 8 FLGA FLGB ...
Page 3
... FLG low OUT = 3.3V, apply until FLG low OUT increasing, Note 5 decreasing, Note 10mA L = 3.3V 10mA 2.4V and on is 0.8V for the MIC2536-2. The enable input has approximately 3 (Note 2) ) ................................... +2.7V to +5. ........ – + .......................................................... 160 C ....................................................... 206 C/W JA Min Typ 0. ...
Page 4
... Timing Diagrams V OUT OUT OUT MIC2536 Device Under OUT Test Functional Characteristics Test Circuit t r 90% 10% Output Rise and Fall Times 50 90% Active-High Switch Delay Times (MIC2536-1) 50 90% Active-Low Switch Delay Times (MIC2536- OUT t f 90% 10% t OFF 10% t OFF 10% Micrel March 2000 ...
Page 5
... INPUT VOLTAGE (V) 5 Micrel Output Rise Time vs. Input Voltage – INPUT VOLTAGE (V) Control Voltage vs. Input Voltage VEN Rising 2 2 1.5 –40 C 1.0 0 INPUT VOLTAGE (V) Current Limit Threshold vs. Input Voltage 300 85 C 290 25 C 280 –40 C 270 260 250 240 INPUT VOLTAGE (V) MIC2536 ...
Page 6
... Functional Characteristics Turn-On / Turnoff (MIC2536- 4 Time (1ms/div) Turnoff (MIC2536- 4 Time (1ms/div) Turnoff (MIC2536- 4 Time (5 s/div) March 2000 MIC2536 Turn-On (MIC2536- 4 Time (1ms/div) Turn-On (MIC2536- 4 (output current limited) Time (1ms/div) Enabled Into Short Circuit (MIC2536- OUT = GND 4 Time (10ms/div) March 2000 Micrel MIC2536 ...
Page 7
... MIC2536 Ramped Into Short Circuit (MIC2536-1) Time (100ms/div) March 2000 4 Thermal Shutdown Current-Loop Response (MIC2536-1) output = open output = ground 4700 F IN Time (5 s/div) 7 Inrush Current (MIC2536- 110 210 310 410 4 Time (5 s/div) MIC2536 Micrel ...
Page 8
... MIC2536 Block Diagram ENA ENB MIC2536 MIC2536 CHARGE GATE PUMP CONTROL THERMAL 1.2V OSC. SHUTDOWN REFERENCE CHARGE PUMP GATE CONTROL GND 8 FLGA DELAY OUTA CURRENT LIMIT IN CURRENT LIMIT OUTB DELAY FLGB March 2000 Micrel ...
Page 9
... Once this current-limit thresh- old is exceeded the device enters constant-current mode. This constant current is specified as the short-circuit current- limit in the “Electrical Characteristics” table important to note that the MIC2536 will deliver load current up to the current-limit threshold before entering current-limited opera- tion. Fault Flag FLGx is an open-drain N-channel MOSFET output ...
Page 10
... This “soft-start” feature effec- = 6V) even for a short tively isolates power supplies from highly capacitive loads by reducing inrush current. Figure 2 shows how the MIC2536 may be used in a hot-plug card application. Overcurrent Transients The MIC2536 incorporates an internal circuit designed to prevent FLG from being asserted due to transient inrush current. Overcurrent events < ...
Page 11
... MIC2536 Universal Serial Bus (USB) Power Distribution Applications The MIC2536 is ideally suited for USB (Universal Serial Bus) power distribution applications. For Bus-Powered hubs, USB requires that each downstream port be switched on or off under control by the host four downstream ports each capable of supplying 100mA at 4.4V minimum are allowed. In ...
Page 12
... Package Information 0.026 (0.65) 0.157 (3.99) 0.150 (3.81) 0.064 (1.63) 0.045 (1.14) 0.122 (3.10) 0.112 (2.84) 0.036 (0.90) 0.032 (0.81) 0.012 (0.03) 0.0256 (0.65) TYP MIC2536 MAX) PIN 1 DIMENSIONS: INCHES (MM) 0.020 (0.51) 0.013 (0.33) 0.050 (1.27) TYP 0.0098 (0.249) 0.0040 (0.102) 0 –8 ...
Page 13
... This information is believed to be accurate and reliable, however no responsibility is assumed by Micrel for its use nor for any infringement of patents or other rights of third parties resulting from its use. No license is granted by implication or otherwise under any patent or patent right of Micrel Inc. March 2000 + 1 (408) 944-0970 http://www.micrel.com FAX WEB © 2000 Micrel Incorporated 13 Micrel MIC2536 ...