MAX749CPA+ Maxim Integrated Products, MAX749CPA+ Datasheet - Page 5
![IC LCD BIAS SUPPLY DGT ADJ 8-DIP](/photos/1/39/13900/175-8-dip_sml.jpg)
MAX749CPA+
Manufacturer Part Number
MAX749CPA+
Description
IC LCD BIAS SUPPLY DGT ADJ 8-DIP
Manufacturer
Maxim Integrated Products
Datasheet
1.MAX749CPA.pdf
(12 pages)
Specifications of MAX749CPA+
Applications
LCD Display
Current - Supply
60µA
Voltage - Supply
2 V ~ 6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Through Hole
Package / Case
8-DIP (0.300", 7.62mm)
Operating Supply Voltage
2 V to 6 V
Maximum Operating Temperature
0 C
Mounting Style
Through Hole
Maximum Power Dissipation
727 mW
Minimum Operating Temperature
+ 70 C
Supply Current
60 uA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The MAX749 is a negative-output inverting power con-
troller that can drive an external PNP transistor or P-
channel MOSFET. An external resistor and an internal
DAC control the output voltage (Figure 1).
The MAX749 is designed to operate from 2V to 6V inputs,
ideal for operation from low-voltage batteries. In systems
with higher-voltage batteries, such as notebook comput-
ers, the MAX749 may also be operated from the regulat-
ed +5V supply. A high-efficiency +5V regulator, such as
the MAX782, is an ideal source for the MAX749. In this
example, the MAX749 efficiency (80%) is compounded
with the MAX782 efficiency (95%): 80% x 95% = 76%,
which is still high.
The MAX749 and the external components shown in the
Typical Operating Circuit form a flyback converter.
When the external transistor is on, current flows through
the current-sense resistor, the transistor, and the coil.
Energy is stored in the core of the coil during this phase,
and the diode does not conduct. When the transistor
Figure 1. Block Diagram, Showing External Circuitry Using a PNP Transistor
_______________Detailed Description
CTRL
ADJ
MAX749
POWER-ON
RESET
LOGIC
_______________________________________________________________________________________
BIAS
ON/OFF
+2V TO +6V
INPUT
Digitally Adjustable LCD Bias Supply
RESET
INCREMENT
Operating Principle
COUNTER
6-BIT
GND
V+
0.1 F
6-BIT
CURRENT-OUTPUT
DAC
SWITCH-
SUPPLY
POWER
MODE
REF
turns off, current flows from the output through the diode
and the coil, driving the output negative. Feedback con-
trol adjusts the external transistor’s timing to provide a
regulated negative output voltage.
The MAX749’s unique control scheme combines the
ultra-low supply current of pulse-skipping, pulse-fre-
quency modulation (PFM) converters with the high full-
load efficiency characteristic of pulse-width modulation
(PWM) converters. This control scheme allows the
device to achieve high efficiency over a wide range of
loads. The current-sense function and high operating
frequency allow the use of tiny external components.
Switching control is accomplished through the combi-
nation of a current limit in the switch plus on- and off-
time limits (Figure 2).
Once turned on, the transistor stays on until either:
- the maximum on-time one-shot turns it off
- the switch current reaches its limit (as determined
(8µs later), or
by the current-sense resistor and the current
comparator).
6.66 A TO 20 A
22 F
6.2V
DLOW
DHI
CS
FB
R
470
C
BASE
COMP
R
FB
Q1
ZTX750
L1
47 H
R
SENSE
D1
1N5819
22 F
30V
(NEGATIVE)
V
OUT
5