IR3500AMPBF International Rectifier, IR3500AMPBF Datasheet - Page 22

• Manufacturer Part Number: IR3500AMPBF
• Description: IC CTRL XPHASE3 VR11.0 32-MLPQ
• Manufacturer: International Rectifier
• Series: XPhase3™r

Specifications of IR3500AMPBF

• Applications: Processor
• Current - Supply: 6.5mA
• Voltage - Supply: 4.75 V ~ 7.5 V
• Operating Temperature: 0°C ~ 100°C
• Mounting Type: Surface Mount
• Package / Case: *
• Package: 32-Lead MLPQ
• Circuit: X-Phase Control IC
• Switch Freq (khz): 250kHz to 1.5MHz
• Pbf: PbF Option Available
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Constant Over-Current Control during Soft Start
The over current limit threshold is set by a resistor connected between OCSET and VDAC. If the IIN pin voltage,
which is proportional to the average current plus VDAC voltage, exceeds the OCSET voltage during soft start, the
constant over-current control is activated. Figure 13 shows the constant over-current control with delay during soft
start. The delay time is set by the ROSC resistor, which sets the number of switching cycles for the delay counter.
The delay is required since over-current conditions can occur as part of normal operation due to inrush current. If an
over-current occurs during soft start (before PGOOD is asserted), the SS/DEL voltage is regulated by the over
current amplifier to limit the output current below the threshold set by OCSET voltage. If the over-current condition
persists after delay time is reached, the fault latch will be set pulling the error amplifier’s output low and inhibiting
switching in the phase ICs. The SS/DEL capacitor will discharge until it reaches 0.2V and the fault latch is reset
allowing a normal soft start to occur. If an over-current condition is again encountered during the soft start cycle, the
constant over-current control actions will repeat and the converter will be in hiccup mode. The delay time is
controlled by a counter which is triggered by clock. The counter values vary with switching frequency per phase in
order to have a similar delay time for different switching frequencies.
Over-Current Hiccup Protection after Soft Start
The over current limit threshold is set by a resistor connected between OCSET and VDAC pins. Figure 13 shows
the constant over-current control with delay after PGOOD is asserted. The delay is required since over-current
conditions can occur as part of normal operation due to load transients or VID transitions.
If the IIN pin voltage, which is proportional to the average current plus VDAC voltage, exceeds the OCSET voltage
after PGOOD is asserted, it will initiate the discharge of the capacitor at SS/DEL. The magnitude of the discharge
current is proportional to the voltage difference between IIN and OCSET and has a maximum nominal value of
55uA. If the over-current condition persists long enough for the SS/DEL capacitor to discharge below the 120mV
offset of the delay comparator, the fault latch will be set pulling the error amplifier’s output low and inhibiting
switching in the phase ICs and de-asserting the PGOOD signal. The output current is not controlled during the
delay time. The SS/DEL capacitor will discharge until it reaches 200 mV and the fault latch is reset allowing a
normal soft start to occur. If an over-current condition is again encountered during the soft start cycle, the over-
current action will repeat and the converter will be in hiccup mode.
ENABLE
VDAC
SS/DEL
VRRDY
(12V)
EAOUT
VOUT
VCC
Page 22 of 48
VID
3.92V
4.0V
1.4V
Figure 12 - Start-up sequence of converter without boot voltage
START DELAY (TD1)
SOFT START
TIME (TD2)
VRRDY DELAY
TIME (TD3)
NORMAL OPERATION
July 28, 2009
IR3500A