ADN8830ACPZ-REEL Analog Devices Inc, ADN8830ACPZ-REEL Datasheet - Page 10
![IC THERMO COOLER CNTRLR 32-LFCSP](/photos/6/49/64957/505-32-lfcsp_sml.jpg)
ADN8830ACPZ-REEL
Manufacturer Part Number
ADN8830ACPZ-REEL
Description
IC THERMO COOLER CNTRLR 32-LFCSP
Manufacturer
Analog Devices Inc
Datasheet
1.ADN8830ACPZ-REEL7.pdf
(24 pages)
Specifications of ADN8830ACPZ-REEL
Applications
Thermoelectric Cooler
Current - Supply
8mA
Voltage - Supply
3.3 V ~ 5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
32-LFCSP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
ADN8830ACPZ-REELTR
ADN8830
To eliminate the resolution of the DAC as the principal source
of system error, the step size of each bit, V
than the desired system resolution. A practical value for absolute
DAC resolution is the equivalent of 0.05 C. The value of V
should be less than the value of m from Equation 8 multiplied
by the desired temperature resolution, or
where m is the slope of the voltage-to-temperature conversion
line, as found from Equation 8. From Design Example 2, where
m = 25 mV/ C, we see the DAC should have resolution better
than 1.25 mV per step.
The minimum number of bits required is then given as
where V
should be equal to the reference voltage from the ADN8830,
VREF = 2.47 V as given in the Specifications table for the
Reference Voltage. In this example, the minimum resolution is
11 bits. A 12-bit DAC, such as the AD7390, can be readily
found.
It is important that the full-scale voltage input to the DAC is tied
to the ADN8830 reference voltage, as shown in Figure 4. This
eliminates errors from slight variances of VREF.
Thermistor Fault and Temperature Lock Indications
Both the THERMFAULT (Pin 1) and TEMPLOCK (Pin 5)
outputs are CMOS compatible outputs that are active high.
THERMFAULT will be a logic low while the thermistor is
operating normally and will go to a logic high if a short or
open is detected at THERMIN (Pin 2). The trip voltage for
THERMFAULT is when THERMIN falls below 0.2 V or
exceeds 2.0 V. THERMFAULT provides only an indication of
a fault condition and does not activate any shutdown or protec-
tion circuitry on the ADN8830. To shut down the ADN8830, a
logic low voltage must be asserted on Pin 3, as described in the
Shutdown Mode section.
TEMPLOCK will output a logic high when the voltage at
THERMIN is within 2.5 mV of TEMPSET. This voltage can
be related to temperature by solving for m from Equation 8. For
most laser diode applications, 2.5 mV is equivalent to 0.1 C.
If the voltage difference between THERMIN and TEMPSET is
greater than 2.5 mV, then TEMPLOCK will output a logic low.
The input offset voltage of the ADN8830 is guaranteed to within
250 V, which for most applications is within 0.01 C.
Setting the Switching Frequency
The ADN8830 has an internal oscillator to generate the switch-
ing frequency for the output stage. This oscillator can be either
set in free-run mode or synchronized to an external clock
signal. For free-run operation, SYNCIN (Pin 25) should be
connected to ground and COMPOSC (Pin 24) should be
connected to AVDD. The switching frequency is then set by a
single resistor connected from FREQ (Pin 26) to ground.
Table I shows R
V
Number of Bits
STEP
FS
is the full-scale output voltage from the DAC, which
0 05
.
FREQ
C m
for some common switching frequencies.
log
V
FS
log 2
– log
V
STEP
STEP
, should be lower
STEP
(10)
(11)
–10–
For other frequencies, the value for this resistor, R
be set to
where f
Higher switching frequencies reduce the voltage ripple across
the TEC. However, high switch frequencies will create more
power dissipation in the external transistors. This is due to the
more frequent charging and discharging of the transistors’ gate
capacitances. If large transistors are needed for a high output
current application, faster switching frequencies could reduce
the overall power efficiency of the circuit. This is covered in
detail in the Calculating Power Dissipation and Efficiency section.
The switching frequency of the ADN8830 can be synchronized
with an external clock by connecting the clock signal to SYNCIN
(Pin 25). Pin 24 should also be connected to an R-C network, as
shown in Figure 6. This network is simply used to compensate a
PLL to lock on to the external clock. To ensure the quickest
synchronization lock-in time, R
The relative phase of the ADN8830 internal oscillator compared
to the external clock signal can be adjusted. This is accomplished
by adjusting the voltage to PHASE (Pin 29) according to TPCs 3
and 4. The phase shift versus voltage can be approximated as
where V
value of 2.47 V.
To ensure the oscillator operates correctly, V
higher than 100 mV and lower than 2.3 V. This is required for
either internal clock or external synchronization operation. A
resistor divider from VREF to ground can establish this voltage
easily, although any voltage source, such as a DAC, could be used
as well. If phase is not a consideration, for example with a single
ADN8830 being used, Pin 29 can be tied to Pin 6, which pro-
vides a 1.5 V reference voltage.
R
Phase Shift
Figure 6. Using an R-C Network on Pin 24 with
an External Clock
FREQ
SWITCH
PHASE
Table I. Switching Frequencies vs. R
150 10
is the voltage at Pin 29, and VREF has a typical
is the switching frequency in Hz.
f
100 kHz
250 kHz
500 kHz
750 kHz
1 MHz
f
ADN8830
SWITCH
SWITCH
360
9
COMPOSC
V
VREF
PHASE
FREQ
FREQ
24
26
R
1.5 M
600 k
300 k
200 k
150 k
should be set to 1.5 M .
FREQ
1.5M
1k
1nF
0.1 F
PHASE
FREQ
should remain
FREQ
, should
REV. C
(12)
(13)